GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2008 🢒 Caprice WM 🢒 Engine 🢒 Engine Electrical 🢒 Battery Positive Cable Replacement

Removal Procedure - Rear

    Important: 

       • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
       • Always route the replacement cable the same as the original cable.

  1. Remove the front seat. Refer to Front Seat Replacement - Bucket.
  2. Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement.
  3. Remove the rear seat back. Refer to Rear Seat Back Replacement.
  4. Remove the left front floor panel carpet. Refer to Front Floor Panel Carpet Replacement.
  5. Remove the rear quarter trim panel. Refer to Quarter Lower Rear Trim Panel Replacement.
  6. Remove the cargo area centre carpet. Refer to Rear Compartment Floor Panel Carpet Replacement
  7. Remove the left-hand cargo area carpet side. Refer to Rear Compartment Side Trim Panel Replacement

    8. Caution: Refer to Battery Disconnect Caution in the Preface section.


    Object Number: 1949822 Size: SH
  8. Disconnect the battery negative cable (1). Refer to Battery Negative Cable Disconnection and Connection.
  9. Disconnect the battery positive cable (2) from the battery.

    10. Object Number: 1949830 Size: SH
  10. Detach the battery post cover (3)..
  11. Press the retaining clip (1) to remove battery post protective cover (4).
  12. Remove the battery post retaining bolt (2).

    13. Object Number: 1949826 Size: SH
  13. Remove the battery positive cable to chassis retaining clips (1).
  14. Remove the battery positive cable from the vehicle.

Installation Procedure - Rear

    Object Number: 1949826 Size: SH
  1. Install the battery positive cable to the vehicle.
  2. Install the battery positive cable to chassis retaining clips (1).

    3. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1949830 Size: SH
  3. Install the battery post retaining bolt (2)

    4. Tighten
    Tighten the post retaining bolt to 15 N·m ( 11 lb ft).

  4. Install the battery post protective cover (4).
  5. Attach the battery post cover (3).

    6. Caution: Refer to Battery Disconnect Caution in the Preface section.


    Object Number: 1949822 Size: SH
  6. Connect the battery positive cable (2) to the battery.
  7. Connect the battery negative cable (1). Refer to Battery Negative Cable Disconnection and Connection.
  8. Install the rear floor panel carpet. Refer to Rear Compartment Floor Panel Carpet Replacement
  9. Install the rear quarter trim panel. Refer to Quarter Lower Rear Trim Panel Replacement.
  10. Install the left front floor panel carpet. Refer to Front Floor Panel Carpet Replacement.
  11. Install the rear seat back. Refer to Rear Seat Back Replacement.
  12. Install the rear seat cushion. Refer to Rear Seat Cushion Replacement.
  13. Install the front seat. Refer to Front Seat Replacement - Bucket.
  14. Install the left-hand cargo area carpet side. Refer to Rear Compartment Side Trim Panel Replacement
  15. Install the cargo area centre carpet. Refer to Rear Compartment Floor Panel Carpet Replacement
  16. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.

Removal Procedure - Front (3.6L Engines)

    Caution: Refer to Battery Disconnect Caution in the Preface section.

  1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Remove the front air deflector. Refer to Front Air Deflector Replacement.

    3. Object Number: 1949830 Size: SH
  3. Detach the battery post cover (3).
  4. Press the retaining clip (1) to remove battery post protective cover (4).
  5. Remove the battery post retaining bolt (2).

    6. Object Number: 1949828 Size: SH
  6. Remove the front battery positive cable from battery post (2).
  7. Remove the front battery positive cable to underhood body electrical centre retaining bolt (1).
  8. Remove the front battery positive cable to alternator retaining nut (4).
  9. Remove the front battery positive cable to chassis retaining clips (3).
  10. Remove the front battery positive cable (5) from the engine compartment.

Installation Procedure - Front (3.6L Engines)

    Object Number: 1949828 Size: SH
  1. Install the front battery positive cable (5) to the engine compartment.
  2. Install the front battery positive cable to chassis retaining clips (3).

    3. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the front battery positive cable to battery post (2).

    4. Tighten
    Tighten the post retaining bolt to 15 N·m ( 11 lb ft).

  4. Install the battery positive cable to underhood body electrical centre retaining nut (1).

    5. Tighten
    Tighten the retaining nut to 10  N·m( 89 lb in).

  5. Install the battery positive cable to alternator battery output terminal, install the retaining nut (4).

    6. Tighten
    Tighten the retaining nut to 13  N·m ( 115 lb in).


    Object Number: 1949830 Size: SH
  6. Install the battery post protective cover (4).
  7. Attach the battery post cover (3).
  8. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.
  9. Install the front air deflector. Refer to Front Air Deflector Replacement.

Removal Procedure - Front (6.0L Engines)

    Caution: Refer to Battery Disconnect Caution in the Preface section.

  1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Remove the front air deflector. Refer to Front Air Deflector Replacement.

    3. Object Number: 1949830 Size: SH
  3. Detach the battery post cover (3).
  4. Press the retaining clip (1) to remove battery post protective cover (4).
  5. Remove the battery post retaining bolt (2).

    6. Object Number: 1949828 Size: SH
  6. Remove the front battery positive cable from battery post (2).
  7. Remove the front battery positive cable to underhood body electrical centre retaining bolt (1).
  8. Remove the front battery positive cable to alternator retaining nut (4).
  9. Remove the front battery positive cable to chassis retaining clips (3).
  10. Remove the front battery positive cable (5) from the engine compartment.

Installation Procedure - Front 6.0L Engines)

    Object Number: 1949832 Size: SH
  1. Install the front battery positive cable (5) to the engine compartment.
  2. Install the front battery positive cable to chassis retaining clips (3).

    3. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the front battery positive cable to battery post (2).

    4. Tighten
    Tighten the post retaining bolt to 15 N·m ( 11 lb ft).

  4. Install the battery positive cable to underhood body electrical centre retaining nut (1).

    5. Tighten
    Tighten the retaining nut to 10  N·m( 89 lb in).

  5. Install the battery positive cable to alternator retaining nut (4).

    6. Tighten
    Tighten the retaining nut to 13  N·m ( 115 lb in).


    Object Number: 1949830 Size: SH
  6. Install the battery post protective cover (4).
  7. Attach the battery post cover (3).
  8. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.
  9. Install the front air deflector. Refer to Front Air Deflector Replacement.

Removal Procedure - Starter (3.6L Engines)

    Caution: Refer to Battery Disconnect Caution in the Preface section.

  1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Remove the front air deflector. Refer to Front Air Deflector Replacement.

    3. Object Number: 1949830 Size: SH
  3. Detach the battery post cover (3).
  4. Press the retaining clip (1) to remove battery post protective cover (4).
  5. Remove the battery post retaining bolt (2).

    6. Object Number: 1949833 Size: SH
  6. Remove the starter battery positive cable from battery post (2).
  7. Remove the starter battery positive cable (3) to starter motor retaining bolt (1).
  8. Remove the front battery positive cable to chassis retaining clips.
  9. Remove the starter battery positive cable (3) from the engine compartment.

Installation Procedure - Starter (3.6L Engines)

    Object Number: 1949833 Size: SH
  1. Install the starter battery positive cable (3) to the engine compartment.

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the starter battery positive cable to battery post (2).

    3. Tighten
    Tighten the post retaining bolt to 15 N·m ( 11 lb ft).

  3. Install the starter battery positive cable to starter motor and install the retaining nut (1).

    4. Tighten
    Tighten the retaining nut to 20  N·m ( 14 lb ft).


    Object Number: 1949830 Size: SH
  4. Install the battery post protective cover (4).
  5. Attach the battery post cover (3).

Removal Procedure - Starter (6.0L Engines)

    Caution: Refer to Battery Disconnect Caution in the Preface section.

  1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Remove the front air deflector. Refer to Front Air Deflector Replacement.

    3. Object Number: 1949830 Size: SH
  3. Detach the battery post cover (3).
  4. Press the retaining clip (1) to remove battery post protective cover (4).
  5. Remove the battery post retaining bolt (2).

    6. Object Number: 1949835 Size: SH
  6. Remove the starter battery positive cable from the battery post (2).
  7. Remove the starter battery positive cable (3) to starter motor retaining bolt (1).
  8. Remove the starter battery positive cable to chassis retaining clips (4).
  9. Remove the starter battery positive cable (3) from the engine compartment.

Installation Procedure - Starter (6.0L Engines)

    Object Number: 1949835 Size: SH
  1. Install the starter battery positive cable (3) to the engine compartment.
  2. Install the starter battery positive cable to chassis retaining clips (4).

    3. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the starter battery positive cable to battery post (2).

    4. Tighten
    Tighten the post retaining bolt to 15 N·m ( 11 lb ft).

  4. Install the starter battery positive cable to starter motor and install retaining nut (1).

    5. Tighten
    Tighten the retaining nut to 20  N·m ( 14 lb ft).


    Object Number: 1949830 Size: SH
  5. Install the battery post protective cover (4).
  6. Attach the battery post cover (3).
  7. Install the front air deflector. Refer to Front Air Deflector Replacement.
  8. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection.