GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2008 🢒 Caprice WM 🢒 General Information 🢒 General Information 🢒 Video Display Replacement

Video Display Replacement Headliner LWB SWB

Removal Procedure

    Object Number: 1957823 Size: SH
  1. Remove the rear dome lamp assembly. Refer to Dome Lamp Replacement .
  2. Remove the DVD screen surround trim. Refer to Video Disc Player Display Bezel Replacement
  3. Remove the DVD screen to rear seat entertainment (RSE) assembly bracket screws (1).

    4. Object Number: 1957827 Size: SH
  4. Disconnect the DVD screen connector (1).
  5. Remove the DVD screen from the RSE assembly bracket.

Installation Procedure

    Object Number: 1957827 Size: SH
  1. Install the DVD screen to the RSE assembly bracket.
  2. Connect the DVD screen electrical connector (1).

    3. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1957823 Size: SH
  3. Install the DVD screen to RSE assembly bracket retaining screws (1).

    4. Tighten
    Tighten the screws to 1.5 N·m (13 lb in).

  4. Install the DVD screen surround trim.Refer to Video Disc Player Display Bezel Replacement
  5. Install the rear dome lamp assembly. Refer to Dome Lamp Replacement .

Video Display Replacement Front Seat Head Restraint LWB

Removal Procedure
  1. Remove the front seat head restraint. Refer to Front Seat Head Restraint Replacement.

    2. Object Number: 1957814 Size: SH
  2. Remove the rear seat entertainment (RSE) head rest escutcheon to head restraint assembly screws (4).

    3. Important: Using an appropriate tool, carefully locate the retaining clip (1) along the upper edge of the escutcheon. Depress the clip and detach the escutcheon slightly. Repeat for the opposite retaining clip and remove the escutcheon.

  3. Remove the escutcheon (2) from the head restraint assembly (3).

    4. Object Number: 1957817 Size: SH
  4. Remove the RSE circuit board to head restraint assembly screws (1).

    5. Object Number: 1957818 Size: SH

    Important: Using an appropriate tool depress the retaining lugs (3), in four places.

  5. Remove the DVD screen bezel (1) from the head restraint (2).

    6. Object Number: 1957819 Size: SH
  6. Disconnect the wiring harness connectors (1) from the top of the DVD screen and remove the circuit board.

    7. Object Number: 1957821 Size: SH
  7. Remove the DVD screen assembly to head restraint assembly screws (4).
  8. Rotate the top of the screen assembly (1) out, and from behind, carefully disconnect the wiring connector (3).
  9. Remove the screen assembly (1) from the head restraint assembly (2).

    10. Object Number: 1957822 Size: SH
  10. Remove the DVD screen to mounting plate screws (4).
  11. Remove the DVD screen (1) from the mounting plate (2).

    12. Important: Repeat step for opposite pivot hinge as required.

  12. Remove the pivot hinge to mounting plate screws (4).
  13. Remove the pivot hinge (3) from the mounting plate (2).

Installation Procedures

    Object Number: 1957822 Size: SH
  1. Install the pivot hinge (3) to the mounting plate (2).

    2. Notice: Refer to Fastener Notice in the Preface section.

    Important: Repeat step for opposite pivot hinge as required.

  2. Install the pivot hinge to mounting plate retaining screws (4).

    3. Tighten
    Tighten the screws to 2 N·m (18 lb in).

  3. Install the DVD screen (1) to the mounting plate (2).

    4. Notice: Refer to Fastener Notice in the Preface section.

  4. Install the DVD screen to mounting plate retaining screws (4).

    5. Tighten
    Tighten the screws to 2 N·m (18 lb in).


    Object Number: 1957821 Size: SH
  5. Install the DVD screen assembly (1) to the head restraint assembly (2).
  6. Carefully connect the wiring connector (3).
  7. Install the DVD screen (1) to the head restraint assembly (2).

    8. Notice: Refer to Fastener Notice in the Preface section.

  8. Install the DVD screen assembly to head restraint assembly retaining screws (4).

    9. Tighten
    Tighten the screws to 2 N·m (18 lb in).


    Object Number: 1957819 Size: SH
  9. Connect the wiring harness connectors (1) to the top of the DVD screen and install the circuit board.

    10. Object Number: 1957818 Size: SH

    Important: Ensure the retaining lugs (3), four places, correctly engage.

  10. Install the DVD screen bezel (1) to the head restraint (2).

    11. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1957817 Size: SH
  11. Install the RSE circuit board to head restraint assembly retaining screws (1).

    12. Tighten
    Tighten the screws to 2 N·m (18 lb in).


    Object Number: 1957814 Size: SH

    Important: Make sure the retaining clips (1) along the upper edge of the escutcheon correctly engage.

  12. Install the escutcheon (2) to the head restraint assembly (3).

    13. Notice: Refer to Fastener Notice in the Preface section.

  13. Install the RSE head restraint escutcheon to head restraint assembly retaining screws (4).

    14. Tighten
    Tighten the screws to 2 N·m (18 lb in).

  14. Install the front seat head restraint. Refer to Front Seat Head Restraint Replacement.