Scan Tool Data List Except Holden
The Engine Scan Tool Data List contains all engine related parameters that are available on the scan tool. The list is arranged in alphabetical order. A parameter may appear in any one of the data lists, and in some cases may appear more than once, or in more than one data list in order to group certain related parameters together.
Use the Engine Scan Tool Data List only after the following conditions are determined:
| • | The Diagnostic System Check - Vehicle is completed. |
| • | There are no diagnostic trouble codes (DTCs). |
| • | The on-board diagnostics are functioning correctly. |
Scan tool values from an engine that is operating correctly may be used for comparison with the engine you are diagnosing. The Engine Scan Tool Data List represents the values that would be seen on a normal operating engine.
Important: Do not use a scan tool that displays faulty data. The scan tool concern should be reported to the manufacturer. Use of a faulty scan tool may result in misdiagnosis and unnecessary parts replacement.
Only the parameters listed below are referenced in this service information for use in diagnosis. If all values are within the typical range described below, refer to Symptoms - Engine Controls for diagnosis.
The column labeled Data List indicates where a parameter is located on the scan tool. Review the scan tool operating manual for the exact locations of the data lists. The following is a description of each term listed:
All: The Parameter is in all data lists indicated below.CH: Cooling/HVAC Data
CMP: CMP Actuator Data
CT: Cruise/Traction Data
Eng: Engine Data
ET: Electrical/Theft Data
EVAP: EVAP Data
FF: Freeze Frame Data
FR: Failure Records
FT: Fuel Trim Data
HO2S: HO2S Data
Ign: Ignition Data
IM: I/M Data
IND: Induction Data
IPC: Instrument Panel Cluster Data
MF: Misfire Data
TAC: TAC Data
Trans: Auto Trans Data
Scan Tool Parameter | Data List | Parameter Range/Units | Typical Data Values |
|---|---|---|---|
Engine Idling/Radiator Hose Hot/Park or Neutral/Closed Loop/Accessories Off | |||
5-Volt Reference 1, 2, or 3 Circuit Status | EVAP, IGN, IND, TAC, CH | OK/Fault | OK |
A/C Disengage 1-8 History | Cooling/HVAC | Reason for A/C Disengagement | Varies |
A/C High Side Pressure | Cooling/HVAC | 0-5 Volts | Varies |
A/C High Side Pressure | Cooling/HVAC | kPa/psi | Varies |
A/C Off for WOT | Cooling/HVAC | Yes/No | No |
A/C Pressure Disable | Cooling/HVAC | Yes/No | No |
A/C Relay Circuit Status | Cooling/HVAC | OK/Fault/Indeterminate | OK |
A/C Relay Command | Eng, TAC, CH, IND, MF | On/Off | Off |
A/C Request Signal | Cooling/HVAC | Yes/No | No |
Air Flow Calculated | ENG, EVAP, FT, HO2S, IND, MF, TAC | g/s | -- |
Air Fuel Ratio | ENG, FT, HO2S, IND | 14.7:1 | Varies |
Ambient Air Temperature | ENG, EVAP | °C/°F | Varies |
APP Indicated Angle | CMP,CT, Eng, ET, EVAP, FT, HO2S, Ign, IND, MF, TAC, Trans | 0-100% | 0% |
APP Sensors | TAC | 0-100% | 0% |
APP Sensor 1 | TAC | 0.9-4.5 Volts | 1 Volt |
APP Sensor 2 | TAC | 0.40-2.25 Volts | 0.4 Volt |
APP Sensor 1 and 2 | TAC | Agree/Disagree | Agree |
BARO | CMP , Eng, EVAP, FT, HO2S, Ign,IM, IND, Trans | 65-104 kPa (8-16 psi) | Varies with altitude |
BARO | IND | Volts | Varies |
Brake Pedal Signal Status | CT, Eng, ET, TAC, Trans | Valid/Invalid | Valid |
Calculated ECT - Closed Loop Fuel Control | CH | -39 to +40°C (-38 to +104°F) | 40°C (104°F) |
Calculated ECT - Thermostat Diagnosis | CH | -39 to +140°C (-38 to +284°F) | 89°C (192°F) |
Calc. TWC Temp. Bank 1 and 2 Sensor 1 and 2 | FT, MF | Temperature | Varies |
Catalytic Converter Protection Active | FT, HO2S | Yes/No | No |
Catalyst Monitor Complete This Ignition | IM | Yes/No | Varies |
Catalyst Monitor Enabled this Ignition | IM | Yes/No | Varies |
CKP Resync Counter | Ign | Counts | 0 Counts |
CKP Active Counter | Ign | Counts | 0 Counts |
CMP Sensor | CMP, IGN, MF | RPM | Engine idle speed |
Cold Startup | ENG, EVAP, IM | YES/NO | Varies |
Crank Request Signal | ET | Yes/No | No |
Cruise Control Active | ENG, TAC | Active/Inactive | Inactive |
Cruise Control Active | CT, Eng, IPC, TAC, | Yes/No | No |
Cruise Disengage 1-8 History | CT | Reason | Varies |
Cruise Inhibited | CT | Yes/No | No |
Cruise On/Off Switch | CT | On/Off | Off |
Cruise Resume/Accel. Switch | CT | ON/OFF | OFF |
Cruise Set/Coast Switch | CT | ON/OFF | OFF |
Cylinder 1-6 IC Circuit Status | MF | OK/Fault/Indeterminate | OK |
Cylinder 1-6 Injector Circuit Status | MF | OK/Fault/Indeterminate | OK |
Cylinder 1-6 Knock Retard | Ign | Degree | 0 Degrees |
Decel. Fuel Cutoff | Eng, FT, HO2S | Active/Inactive | Inactive |
Desired Exh. CMP Bank 1 or 2 | CMP | Degree | Varies |
Desired Idle Speed | Eng, EVAP, CMP, CT, IND | 0-7,000 RPM | 650 RPM |
Desired Int. CMP Bank 1 or 2 | CMP | Degrees | Varies |
Distance Since DTC Cleared | ENG | Miles/Kilometers | Varies |
DTC Set This Ignition | Eng | Yes/No | No |
EC Ignition Relay Command | Eng, ET,TAC | On/Off | On |
EC Ignition Relay Circuit Status | ET | OK/Fault/Indeterminate | OK |
EC Ignition Relay Feedback Signal | Eng, TAC, ET | 0-25.5 Volts | 12.0-14.5 Volts |
ECM in VTD Fail Enable | ET | Yes/No | No |
ECT Sensor | ALL | -39°C to +140°C (-38°F to +284°F) | Varies |
Engine Load | CH, CMP, Eng, EVAP, FF, FR, FT, ,HO2S, Ign, IND, MF, TAC, Trans | 0-99% | 25-45% - Idle 40-60% - 2500 RPM |
Engine OFF EVAP Test Conditions Met | EVAP | Yes/No | Varies |
Engine Off Time | EVAP, IM | 0:00:00 Seconds | Varies |
Engine Oil Life Remaining | CMP, IPC | % | Varies |
Engine Oil Pressure Sensor | IPC | 1-5 Volts | Varies |
Engine Oil Pressure Sensor | CMP, Eng, ET, IPC, MF, | kPa/psi | Varies |
Engine Oil Temperature Calculated | CH, CMP, IPC | °C (°F) | Varies |
Engine Run Time | Eng, Ign, EVAP, FT, HO2S, IM, MF, TAC, CMP, CH, CT, IND, Trans | 0:00:00 | Varies |
Engine Speed | CH, CMP, CT, Eng, ET, EVAP, FF, FR, FT, ,HO2S, Ign, IND, IPC, MF, TAC, Trans | RPM | 575-700 RPM |
EVAP Fault History | EVAP | Vacuum/Purge Valve Leak/Small Leak/Weak Vacuum/No Test Result | No Test Result |
EVAP Monitor Complete This Ignition | IM | Yes/No | Varies |
EVAP Monitor Enabled This Ignition | IM | Yes/No | Varies |
EVAP Purge Solenoid Circuit Status | EVAP | OK/Fault/Indeterminate | OK |
EVAP Purge Solenoid Command | Eng, EVAP, FT, H02S | 0-100% | Varies |
Exh. CMP Angle Bank 1 or 2 | CMP | Degrees | Varies |
Exh. CMP Bank 1 or Bank 2 Active Counter | CMP, IGN | Counts | Varies |
Exh. CMP Bank 1 or 2 Command | CMP | 0-99% | Varies |
Exh. CMP Angle Bank 1 or 2 Variance | CMP | Degrees | Varies |
Exh. CMP Solenoid Bn. 1 or 2 Circuit Status | CMP | OK/Fault/Indeterminate | OK |
FC Relay 1 Circuit Status | CH | OK/Fault/Indeterminate | OK |
FC Relay 2 and 3 Circuit Status | CH | OK/Fault/Indeterminate | OK |
FC Relay 1 Command | CH | On/Off | Varies |
FC Relay 2 and 3 Command | CH | On/Off | Varies |
Fuel Level Sensor Left Tank (Secondary) Fuel Level Sensor Right Tank (Primary) | EVAP | 0-5 Volts | Varies |
Fuel Pump Relay Circuit Status | Eng | OK/Fault/Indeterminate | OK |
Fuel Pump Relay Command | Eng | On/Off | On |
Fuel Tank Level Remaining | Eng, EVAP, FT, IM, IPC MF, | Liter/Gallon/Percent | Varies |
Fuel Tank Rated Capacity | EVAP | Liter/Gallon | 19.9 Gallons (75.3 Liters) |
Fuel Trim Learn | FT | Enabled/Disabled | Enabled |
GEN L-Terminal Signal Command | ET | ON/OFF | ON |
Generator F-Terminal Signal | ET | 0-100% | Varies |
HO2S Bank 1 or 2 Sensor 1 | Eng, EVAP, FT, HO2S, IND | Lambda | 1.0 Lambda |
HO2S Bank 1 or 2 Sensor 2 | Eng, EVAP, FT, HO2S, IND | 0-1,006 mV | Varies 400-700 mV |
HO2S Heater Monitor Complete This Ignition | IM | Yes/No | Varies |
HO2S Heater Monitor Enabled This Ignition | IM | Yes/No | Varies |
HO2S Htr. Bn. 1 or 2 Sensor 1 or 2 Circuit Status | H02S | OK/Fault/Indeterminate | OK |
HO2S Bank 1 or 2 Sensor 1 or 2 Heater Command | HO2S | 0-99% | Varies |
HO2S Bank 1 or 2 Sensor 1 or 2 Heater Command | HO2S | ON/OFF | ON |
HO2S/O2S Monitor Complete This Ignition | IM | Yes/No | Varies |
HO2S/O2S Monitor Enabled This Ignition | IM | Yes/No | Varies |
HO2S Sensing Element Bn. 1 or 2 Sensor 1 | HO2S | Ohms | 70-90 Ohms Depends on Temperature |
HO2S Sensing Element Bn. 1 or 2 Sensor 2 | HO2S | Ohms | 20-300 Ohms Depends on Temperature |
IAT Sensor | CH, CMP, Eng, EVAP, FF, FR, FT, HO2S, Ign, IM, IND, MF, TAC,Trans | -39° to +140°C (-38° to +284°F) | Varies |
Ignition Off Time | ENG, EVAP, IM | 0:00:00 | Varies |
Ignition 0 Signal | Eng, ET, Ign, IM, IPC, TAC | On/Off | On |
Ignition 1 Signal | ALL | Volts | B+ |
Ignition 1 Signal | Eng, ET, EVAP | On/Off | On |
IMRC Solenoid Circuit Status | IND | OK/Fault/Indeterminate | OK |
IMRC Solenoid Command | IND | On/Off | Off |
Initial Brake Apply Signal | CT, Eng, ET, IM, TAC, Trans | Applied/Released | Released |
Injector 1-6 Command | FT, MF | ms | Varies |
Injector 1-6 Disabled Due to Misfire | FT, MF | YES/NO | NO |
Int. CMP Angle Bank 1 or 2 | CMP | Degrees | Varies |
Int. CMP Bank 1 or Bank 2 Active Counter | CMP, IGN | Counts | Varies |
Int. CMP Angle Bank 1 or 2 Variance | CMP | Degrees | Varies |
Int. CMP Bank 1 or 2 Command | CMP | 0-99% | Varies |
Int. CMP Solenoid Bn. 1 or 2 Circuit Status | CMP | OK/Fault/Indeterminate | OK |
Knock Detected Cyl.1-6 | IGN | YES/NO | NO |
Knock Retard | Ign | Degrees | Varies |
KS 1 or 2 Signal | Ign | Volts | Varies |
Long Term FT Bank 1 or Bank 2 | CMP, ENG, EVAP, FT, HO2S | -100 to +100% | 7-9% |
Loop Status Bn 1 or 2 Sen. 1 | Eng, EVAP, FF, FR, FT, HO2S, | Open Loop/Closed Loop | Closed Loop |
Loop Status Bn 1 or 2 Sen. 2 | Eng, EVAP, FF, FR, FT, HO2S, | Open Loop/Closed Loop | Open Loop |
LT FT Bn. 1 or Bn. 2 Idle/Decel. | Eng, EVAP, FT, HO2S | -100% to +100% | 0% |
MAF Performance Test | IND, TAC | OK/Fault | OK |
MAF Sensor | CMP, Eng, EVAP, FF, FR, FT, HO2S, Ign, IND, MF, TAC, Trans | 0-655 g/s | 3.4-6.3 g/s |
MAF Sensor | IND | 0-9999 Hz | 2000-2300 Hz |
MIL Circuit Status | Eng, IPC | OK/Fault/Indeterminate | OK |
MIL Command | Eng, IPC, IM | On/Off | Off |
Mil Requested by DTC | CMP, Eng, EVAP, FF, FR, FT, IM, HO2S, Ign, IND, MF, TAC, Trans | Yes/No | No |
Mileage Since DTC First Failure | FF, FR | km - miles | Varies |
Mileage Since DTC Last Failure | FF, FR | km - miles | Varies |
Mileage Since MIL Requested | FF, FR | km - miles | Varies |
Misfire Current Cyl. 1-6 | MF | 0-255 Counts | 0 |
Misfire History Cyl. 1-6 | MF | 0-65,535 Counts | 0 |
Moderate Brake Apply Signal | CT, TAC | Applied/Released | Released |
PNP Switch | Eng | Park/Neutral/In Gear | P/N |
Power Enrichment | Eng, FT, HO2S, MF | Active/Inactive | Inactive |
Reduced Engine Power | TAC | Active/Inactive | Inactive |
RVS Disable 1-8 History | ET | None | Varies |
Short Term FT Bank 1 or Bank 2 | Eng, EVAP, FT, HO2S, FF, FR | -25% to +25% | -3% to +3% |
Spark | Eng, Ign, FT, HO2S, MF, CH, CT, IND, FF, FR | -20 to +40 Degrees | 2-10 Degrees |
Starter Relay Circuit Status | ET | OK/Fault/Indeterminate | OK |
Starter Relay Command | CT, ET | On/Off | Off |
Start Up ECT | CH, EVAP, HO2S, IM | -39° to +140°C (-38° to +284°F) | Varies |
Start Up IAT | CH, EVAP, HO2S, IM | -39° to +140°C (-38° to +284°F) | Varies |
Stoplamp Pedal Switch | CT, ET, IM, TAC | Applied/Released | Released |
System Power Mode | Eng, ET, EVAP, TAC | Off, Accessory, RAP, Run, or Crank Request | Run |
TAC Forced Engine Shutdown | TAC | YES/NO | NO |
TAC Motor | TAC | Enabled/Disabled | Enabled |
TAC System Learned Counts | TAC | 0-11 Counts | 11 |
TCC Status | MF | Locked/Unlocked | Unlocked |
TCM Requested Torque | Trans | N·m/lb ft | Varies |
TCM Torque Increase | CT, TAC, Trans | Yes/No | NO |
TCS Torque Increase | CT, TAC | Yes/No | NO |
TCS Torque Reduction Active | CT, TAC, Trans | Yes/No | NO |
TCM Torque Reduction Active | CT, TAC, Trans | Yes/No | NO |
TCS Torque Delivered Signal | CT, TAC | 0-100% | O% |
TCS Torque Request Signal | CT, TAC, Trans | 0-100% | 90-98% |
Total Fuel Trim Avg. Bank 1 or Bank 2 | EVAP, FT, HO2S | -100 to +100% | Varies |
Total Knock Retard | IGN, CH | Degrees | 0 |
Total Misfire Count | MF | Counts | 0 |
TP Desired Angle | Eng, EVAP, TAC | 0-100% | Varies |
TP Indicated Angle | CMP, CT, Eng, EVAP, FT, ,FF, FR, HO2S, Ign, IND MF, TAC, Trans | 0-100% | Varies |
TP Performance Test | IND, TAC, FT | Active/Inactive | Inactive |
TP Sensor 1 | TAC | 4.5-5.0Volts 4.0 | 0.5-4.50 Volts |
TP Sensor 1 Learned Minimum | TAC | 0-5 Volts | 0.5-4.50 Volts |
TP Sensor 2 | TAC | 0-5 Volts | 5.0-1.0 Volts |
TP Sensor 2 Learned Minimum | TAC | 0-5 Volts | 5.0-1.0 Volts |
TP Sensors 1 and 2 | TAC | Agree/Disagree | Agree |
Traction Control Status | TAC, CT | Active/Inactive | Inactive |
Vehicle Speed Sensor | All | Km/h mph | Varies |
Volumetric Efficiency | Eng, Ign, EVAP, FT, HO2S, MF, TAC, CMP, CH, Trans | 0-100% | 5-25% - Idle and at 2,500 RPM |
VTD Auto. Learn Timer | ET | Active/Inactive | Inactive |
VTD Fuel Disable | ET | Active/Inactive | Inactive |
VTD Fuel Enabled | ET | Yes/No | Yes |
VTD Fuel Disable Untill Ign. Off | ET | Yes/No | No |
VTD Password learned | ET | Yes/No | Yes |
Warm Ups Since DTC Cleared | Eng | Counts | Varies |
Wide Open Throttle | TAC | Yes/No | NO |
Scan Tool Data List Holden
The Engine Scan Tool Data List contains all engine related parameters that are available on the scan tool. The list is arranged in alphabetical order. A parameter may appear in any one of the data lists, and in some cases may appear more than once, or in more than one data list in order to group certain related parameters together.
Use the Engine Scan Tool Data List only after the following conditions are determined:
| • | The Diagnostic System Check - Vehicle is completed. |
| • | There are no diagnostic trouble codes (DTCs). |
| • | The on-board diagnostics are functioning correctly. |
Scan tool values from an engine that is operating correctly may be used for comparison with the engine you are diagnosing. The Engine Scan Tool Data List represents the values that would be seen on a normal operating engine under the conditions specified in the first row of the Scan Tool Data List table.
Important: Do not use a scan tool that displays faulty data. The scan tool concern should be reported to the manufacturer. Use of a faulty scan tool may result in misdiagnosis and unnecessary parts replacement.
Only the parameters listed below are referenced in this service information for use in diagnosis. If all values are within the typical range described below, refer to Symptoms - Engine Controls for diagnosis.
Scan Tool Parameter | System State | Expected Value | Description |
|---|---|---|---|
Engine Idling / Operating Temperature / Closed Throttle / Park or Neutral / Closed Loop / Accessories Off | |||
5V Reference Voltage Circuit 1 Status | Valid Invalid | - | This parameter displays the diagnostic state of the output driver for the 5-volt reference circuit. |
5V Reference Voltage Circuit 2 Status | Valid Invalid | - | This parameter displays the diagnostic state of the output driver for the 5-volt reference circuit. |
5V Reference Voltage Circuit 3 Status | Valid Invalid | - | This parameter displays the diagnostic state of the output driver for the 5-volt reference circuit. |
A/C Cutoff Mode (Air Conditioning) | - | This parameter displays the A/C cutoff mode status. | |
A/C Disengagement 1st History | Eng Speed | - | This parameter displays the Disengagement History status. |
A/C Disengagement 2nd History | Full Load | ||
A/C Disengagement 3rd History | Performance | ||
A/C Disengagement 4th History | Eng Temp | ||
A/C Disengagement 5th History | Not Present | ||
A/C Disengagement 6th History | High Pressure | ||
A/C Disengagement 7th History | Low Battery | ||
A/C Disengagement 8th History | Stall Prevention | ||
A/C Pressure Sensor (Air Conditioning) | - | V | This parameter displays the voltage from the A/C high side pressure sensor signal circuit to the control module. |
A/C Pressure Sensor (Air Conditioning) | - | kPa | This parameter displays the pressure in KPA from the A/C high side pressure sensor signal circuit to the control module. |
A/C Relay (Air Conditioning) | On Off | - | This parameter displays the state of the air conditioning (A/C) clutch relay control circuit as commanded by the control module. |
A/C Request | No Yes | - | This parameter displays the state of the A/C request input to the control module from the heating, ventilation, and air conditioning (HVAC) controls. |
A/C Request (Air Conditioning) | On Off | - | This parameter displays the state of the A/C request input to the control module from the heating, ventilation, and air conditioning (HVAC) controls. |
Actual Air/Fuel Ratio | - | 1 | This parameter displays the ratio of air to fuel as calculated by the control module based on various sensor inputs. |
Actual Gear | 1, 2, 3, 4, 5 P/N R Invalid | - | This parameter displays the actual gear selected. |
Alternator F Terminal | - | % | This parameter displays the amount of generator on-time as commanded by the control module. The higher the percentage the greater the generator output. |
Alternator L Terminal Circuit Status | - | This parameter displays if the engine control module is allowing the generator to operate. | |
Alternator L Terminal Duty Cycle | - | % | |
Ambient Temperature | - | °C | This parameter displays the temperature of the ambient air as calculated by the control module based on the input from the ambient air temperature sensor. |
APP Sensor 1 (Accelerator Pedal Position) | - | V | This parameter displays the actual voltage of the accelerator pedal position (APP) sensor 1 signal circuit as measured by the control module. |
APP Sensor 1-2 Correlation (Accelerator Pedal Position) | Okay Fault | - | This parameter displays Fault if the control module detects the signal voltage from APP sensor 1 is not in correct relationship to APP sensor 2. The scan tool displays Okay under the normal operating conditions. |
APP Sensor 2 (Accelerator Pedal Position) | - | V | This parameter displays the actual voltage of the accelerator pedal position (APP) sensor 2 signal circuit as measured by the control module. |
APP Sensors (Accelerator Pedal Position) | - | % | This parameter displays the angle of the accelerator pedal position (APP) as calculated by the control module using the signals from the APP sensors. |
B1 and B2 Actual Exhaust Camshaft Position | - | °CA | This parameter displays the actual exhaust camshaft position in degrees. |
B1 and B2 Actual Intake Camshaft Position | - | °CA | This parameter displays the actual Intake camshaft position in degrees. |
B1 and B2 Catalyst Temperature | - | °C | This parameter displays the catalytic converter temperature as calculated by the engine control module. |
B1 and B2 Commanded Exhaust Camshaft Position (Bank 1) | - | % | This parameter displays the exhaust camshaft position in percent of range as commanded by the control module. |
B1 and B2 Commanded Exhaust Camshaft Position (Bank 1) | - | °CA | This parameter displays the actual exhaust camshaft position in degrees. |
B1 and B2 Commanded Intake Camshaft Position (Bank 1) | - | % | This parameter displays the intake camshaft position in percent of range as commanded by the control module. |
B1 and B2 Commanded Intake Camshaft Position (Bank 1) | - | °CA | This parameter displays the actual intake camshaft position in degrees. |
B1 and B2 Exhaust Camshaft Position Sensor Active Counter | - | Counts | This parameter displays an incrementing counter when the control module receives a signal from the exhaust camshaft position (CMP) sensor. |
B1 and B2 Exhaust Camshaft Position Solenoid Valve Circuit Status | Ok Undefined Status Fault | - | This parameter displays the state of the exhaust camshaft actuator solenoid control circuit. |
B1 and B2 Intake Camshaft Position Sensor Active Counter | - | Counts | This parameter displays an incrementing counter when the control module receives a signal from the intake camshaft position (CMP) sensor. |
B1 and B2 Intake Camshaft Position Solenoid Valve Circuit Status | Ok Undefined Status Fault | - | This parameter displays the state of the intake camshaft actuator solenoid control circuit. |
B1 and B2 LTFT Cruise/Acceleration (Long Term Fuel Trim) | - | % | This parameter is calculated by the control module based on the Short Term FT value. The Long Term FT is used for the long term correction of the fuel delivery. The scan tool will display a high value for a large amount of long term fuel correction, and 0 percent for no long term fuel trim correction. The scan tool will display a negative value when fuel system is running too rich and fuel is being removed from the combustion event. The scan tool will display a positive value if the fuel system is running lean and fuel is being added to the combustion event. |
B1 and B2 LTFT Idle/Deceleration (Long Term Fuel Trim) | - | ||
B1 and B2 Short Term Fuel Trim | - | % | This parameter displays the short-term correction to the fuel delivery by the control module in response to oxygen sensor 1 or 2. If the oxygen sensor indicates a lean air/fuel mixture, the control module will add fuel increasing the short term fuel trim above 0. If the oxygen sensor indicates a rich air/fuel mixture, the control module will reduce fuel decreasing the short term fuel trim below 0. |
B1 and B2 Total Fuel Trim | - | % | This parameter displays the overall fuel trim from the idle/decel cell and the cruise/accel cell. |
B1S1 O2 Sensor (Bank 1 Sensor 1) | - | 0.99 | |
B1S1 O2 Sensor Heater (Bank 1 Sensor 1) | - | Ohm | |
B1S1 O2 Sensor Heater (Bank 1 Sensor 1) | Active Inactive | - | This parameter displays the status of the O2 Sensor Heater. |
B1S1 O2 Sensor Heater Circuit Status (Bank 1 Sensor 1) | Ok Undefined Status Fault | - | This parameter displays the status of the O2 Sensor Heater Circuit. |
B1S2 O2 Sensor (Bank 1 Sensor 2) | - | mV | |
B1S2 O2 Sensor Heater (Bank 1 Sensor 2) | Active Inactive | - | This parameter displays the status of the O2 Sensor Heater. |
B1S2 O2 Sensor Heater Circuit Status (Bank 1 Sensor 2) | Ok Undefined Status Fault | - | This parameter displays the status of the O2 Sensor Heater Circuit. |
B2S1 O2 Sensor (Bank 2 Sensor 1) | - | 0.99 | |
B2S1 O2 Sensor Heater (Bank 2 Sensor 1) | - | Ohm | |
B2S1 O2 Sensor Heater (Bank 2 Sensor 1) | Active Inactive | - | This parameter displays the status of the O2 Sensor Heater. |
B2S1 O2 Sensor Heater Circuit Status (Bank 2 Sensor 1) | Ok Undefined Status Fault | - | This parameter displays the status of the O2 Sensor Heater Circuit. |
B2S2 O2 Sensor (Bank 2 Sensor 2) | - | mV | |
B2S2 O2 Sensor Heater (Bank 2 Sensor 2) | Active Inactive | - | This parameter displays the status of the O2 Sensor Heater. |
B2S2 O2 Sensor Heater Circuit Status (Bank 2 Sensor 2) | Ok Undefined Status Fault | - | This parameter displays the status of the O2 Sensor Heater Circuit. |
Barometric Pressure | - | kPa | This parameter displays the barometric pressure in KPA. |
Barometric Pressure | - | V | This parameter displays the barometric pressure in Voltage. |
Brake Lamp Switch | Active Inactive | - | The scan tool displays Active / Inactive. The scan tool displays Inactive when the ignition is ON and the brake pedal is not applied. |
Calculated Air Flow | - | g/s | |
Calculated ECT - Closed Loop Fuel Control (Engine Coolant Temperature) | - | °C | This parameter displays the calculated air flow into the engine that is based on manifold absolute pressure. The calculation is used in several diagnostics to determine when to run the diagnostics. |
Calculated ECT - Thermostat Diagnosis (Engine Coolant Temperature) | - | °C | This parameter displays the modeled temperature that the control module calculates from air entering the engine, coolant temperature, and ambient air temperature. If the actual engine coolant temperature does not reach this calculated temperature within a predetermined amount of time, a DTC will set. |
Calculated Pedal Position | - | % | This parameter displays the angle of the accelerator pedal as calculated by the engine control module using the signals from the accelerator pedal position sensors. The APP indicated angle is a range of values indicating a low percentage when the accelerator pedal is not pressed to a high percentage when the accelerator pedal is fully pressed. |
Calculated Throttle Position | - | % | This parameter displays the percent of throttle opening as calculated by the control module using information from the TP sensor. |
Camshaft Active Counter | - | Counts | This parameter displays the CMP active counts. |
CC Disengagement 1st History (Cruise Control) | Brake Brake Cruise Cancel Switch | - | The parameter displays the last 8 cruise control disengages in order from 1 to 8, with 8 being the most recent. There are about 20 possible causes for the cruise control to disengage. |
CC Disengagement 2nd History (Cruise Control) | Clutch Disengage Coast Disengage Coast Speed Low | ||
CC Disengagement 3rd History (Cruise Control) | ETC Inhibit High Accel High Decel | ||
CC Disengagement 4th History (Cruise Control) | High Speed Illegal Mode Low Speed | ||
CC Disengagement 5th History (Cruise Control) | Not Present Off Switch Overspeed | ||
CC Disengagement 6th History (Cruise Control) | PCM Inhibit Command Error TCS Active | ||
CC Disengagement 7th History (Cruise Control) | Device Control Memory Error Engine R | ||
CC Disengagement 8th History (Cruise Control) | - | ||
Cold Startup | No Yes | - | This parameter indicates whether the engine meets the conditions for a cold start-up during the present ignition cycle. The scan tool displays Yes when the conditions for a cold start-up are met during this ignition cycle. The scan tool displays No when the conditions for a cold start-up are not met during the present ignition cycle. Conditions for a cold start-up require the coolant temperature and the intake air temperature to be below a predetermined temperature and within a certain range of each other. These conditions must occur after the engine was warmed up to a specific temperature during the previous ignition cycle. |
Commanded B1S1 O2 Sensor Heater (Bank 1 Sensor 1) | - | % | |
Commanded B1S1 O2 Sensor Value (Bank 1 Sensor 1) | - | 0.99 | |
Commanded B1S2 O2 Sensor Heater (Bank 1 Sensor 2) | - | % | |
Commanded B2S1 O2 Sensor Heater (Bank 2 Sensor 1) | - | % | |
Commanded B2S1 O2 Sensor Value (Bank 2 Sensor 1) | - | 0.99 | |
Commanded B2S2 O2 Sensor Heater (Bank 2 Sensor 2) | - | % | |
Coolant Temperature | - | °C | This parameter displays the temperature of the engine coolant based on input to the control module from the engine coolant temperature (ECT) sensor. |
Crank Request | Active Inactive | - | This parameter displays whether the ignition switch has been cycled to the crank position requesting the engine control module to activate the starter relay. |
Crankshaft Active Counter | - | Counts | This parameter displays an incrementing counter when the engine control module receives a signal from the crankshaft position (CKP) sensor. |
Crankshaft Resynchronise Counter | - | Counts | This parameter displays the number of times the engine control module re-syncs with the crankshaft position (CKP) sensor. |
Cruise Control Active | No Yes | - | This parameter displays the status of the cruise control system as determined by the engine control module. The scan tool will display Yes when the cruise control system is in control of vehicle speed. The scan tool will display No when the cruise control system is not operating. |
Cruise Control Disengagement Reason | None Brake Brake Cruise Clutch Disengage Coasting Throttle Control Max Acceleration High Decel High Speed Illegal Mode Low Speed Not Present Off Over speed PCM Command Error Error Traction Ignition Off Data Error System Error Engine Runtime Engine Speed | - | This parameter displays the status of the Cruise Control Disengagement. |
Cruise Control Switch | Inactive Active | - | This parameter displays the status of the Cruise Control Switch. |
Cruise Resume / Acceleration Switch | Inactive Active | - | This parameter displays the status of the Cruise Resume/Acceleration switch. |
Cruise Set / Decel Switch | Inactive Active | - | This parameter displays the status of the Cruise Set/Deceleration switch. |
Cycles Of Misfire | - | Counts | This parameter displays the Cycles of Misfire. |
Cylinder 1 Ignition Circuit Status | Passed Failed Incomplete | - | This parameter displays the status of the Cylinder ignition circuits. |
Cylinder 2 Ignition Circuit Status | |||
Cylinder 3 Ignition Circuit Status | |||
Cylinder 4 Ignition Circuit Status | |||
Cylinder 5 Ignition Circuit Status | |||
Cylinder 6 Ignition Circuit Status | |||
Cylinder 1 Injector Circuit Status | OK Undefined Status Fault | - | This parameter displays the state of the fuel injector control circuit. The parameter displays Fault if the fuel injector control circuit is open, shorted to ground, or shorted to voltage. This parameter displays indeterminate until the control circuit has been commanded ON. |
Cylinder 2 Injector Circuit Status | |||
Cylinder 3 Injector Circuit Status | |||
Cylinder 4 Injector Circuit Status | |||
Cylinder 5 Injector Circuit Status | |||
Cylinder 6 Injector Circuit Status | |||
Cylinder 1 Knock Detected | No Yes | - | This parameter displays the knock retard as commanded by the engine control module for cylinders 1-6. Each cylinder is controlled individually based on both knock sensor signal inputs. |
Cylinder 2 Knock Detected | |||
Cylinder 3 Knock Detected | |||
Cylinder 4 Knock Detected | |||
Cylinder 5 Knock Detected | |||
Cylinder 6 Knock Detected | |||
Dec. Fuel Cutoff (Deceleration) | Inactive Active | - | This parameter displays the status of the operating mode of the engine control module used to turn off the fuel injectors and the evaporative emission (EVAP) canister purge valve during certain deceleration conditions. |
Desired Engine Idle Speed | - | RPM | This parameter displays the desired engine idle speed as commanded by the engine control module. |
Desired Throttle Position | - | 0 - 100 % | This parameter displays the angle of the throttle position (TP) in percent. This information is calculated by the engine control module using the signals from the throttle position sensors. The scan tool will display a low percentage when the throttle plates are closed. The scan tool will display a high percentage when the throttle plates are fully open. |
Distance Since DTC Cleared | - | km | This parameter displays the distance accumulated since an emission diagnostic trouble code was cleared. The scan tool will display increasing distance as the vehicle is driven. |
Electronic Throttle Control Learn Counter | - | Counts | This parameter displays the Electronic Throttle Control Learn. |
Engine Control Ignition Relay | On Off | - | This parameter displays the state of the control circuit engine control module power relay as commanded by the engine control module. The scan tool displays ON with the engine running. |
Engine Control Ignition Relay Circuit Status | Passed Failed Incomplete | - | This parameter displays the status of the output driver for the EC Ignition Relay control circuit. The scan tool will display Passed/Failed or Incomplete. The scan tool will display Passed if the circuit is operating correctly. The scan tool will display Failed if there is an open, short to ground, or a short to voltage on the circuit. |
Engine Control Ignition Relay Feedback | - | V | This parameter displays the voltage of the control circuit engine control module power relay as commanded by the engine control module. |
Engine Load | - | % | This parameter displays the calculated engine load in percent based on inputs to the control module from various engine sensors. |
Engine Oil Level Switch | Ok Low | - | This parameter displays if the level of the engine oil is within range as determined by the engine control module from information received from the engine oil level switch. |
Engine Oil Life Remaining | - | % | This parameter displays the percent of engine oil life remaining. The controller calculates the engine oil life by monitoring engine load, coolant temperature, and engine speed. |
Engine Oil Pressure | - | kPa | This parameter displays the engine oil pressure. |
Engine Oil Pressure | Ok Low | - | This parameter displays Okay if the engine oil pressure is within the correct range. If the engine control module detects that the engine oil pressure is not within the correct range, the scan tool displays Low. |
Engine Oil Pressure Sensor | - | V | The scan tool displays Volts. The scan tool displays the Volts coming back from the sensor when the ignition is ON. |
Engine Oil Temperature Calculated | - | °C | This parameter displays the temperature of the engine oil. |
Engine Oil Temperature Sensor | - | °C | This parameter displays the temperature of the engine oil. |
Engine Runtime | - | h:m:s | This parameter displays the time elapsed since the engine was started. |
Engine Speed | - | RPM | This parameter displays the speed of the engine crankshaft rotation from information received from the crankshaft position (CKP) sensor. |
EVAP Purge Solenoid (Evaporative Emission) | - | % | This parameter displays the on-time or duty cycle of the EVAP canister purge solenoid commanded by the control module. |
EVAP Purge Solenoid Valve Circuit Status (Evaporative Emission) | OK Undefined Status Fault | - | This parameter displays the status of the EVAP Purge Solenoid Valve Circuit. |
Fan Relay 1 | On Off | - | This parameter displays the state of the fan relay control circuit. The parameter displays Fault if the fan relay control circuit is open, shorted to ground, or shorted to voltage. The parameter displays Indeterminate until the circuit has been commanded ON. |
Fan Relay 1 Circuit Status | OK Undefined Status Fault | - | This parameter displays the status of the Fan Relay 1 Circuit. |
Fan Relay 2 and 3 | On Off | - | This parameter displays the engine control module commanded state of the fan relay control circuit. |
Fan Relay 2 and 3 Circuit Status | OK Undefined Status Fault | - | This parameter displays the status of the Fan Relay 2 and 3 Circuits. |
Fuel Level | - | Liters | This parameter displays the amount of fuel remaining in all fuel tanks of the vehicle as measured in liters or gallons. The engine control module calculates the amount of fuel remaining in the tank by using information from the fuel level sensors. |
Fuel Level Sensor Primary | - | V | This parameter displays the voltage signal received by the control module from the fuel level sensor Primary. |
Fuel Level Sensor Secondary | - | V | This parameter displays the voltage signal received by the control module from the fuel level sensor Secondary. |
Fuel Pump Relay | On Off | - | This parameter displays the control modules commanded state of the fuel pump relay control circuit. |
Fuel Pump Relay Circuit Status | OK Undefined Status Fault | - | This parameter displays the status of the Fuel Pump Relay Circuit. |
Fuel System Status | Open Loop Closed Loop | - | The scan tool displays Open Loop or Closed Loop. The scan tool displays Closed Loop if the engine control module is controlling the fuel delivery according to the heated oxygen sensor (HO2S) voltages. The scan tool displays open loop if the engine control module is not adjusting for HO2S inputs. In open loop the engine control module bases fuel deliver on throttle position, engine coolant temperature, and mass airflow sensor inputs. |
Fuel Trim Learn | Disabled Enabled | - | The scan tool displays Enabled or Disabled. When conditions are appropriate for enabling long term fuel trim corrections, the scan tool displays Enabled. If the scan tool displays Disabled, then long term fuel trim will not respond to changes in short term fuel trim. |
Ignition Accessory Signal | On Off | - | This parameter displays the state of the ignition input to the engine control module from the ignition switch. The scan tool will display ON when the ignition switch is in the ignition accessory position. The scan tool will display OFF when the ignition switch is in any other position. |
Ignition Off Time | - | h:m:s | This parameter displays the time elapsed since the engine was started. |
Ignition Voltage | - | V | The scan tool displays Volts. The scan tool displays Volts when the ignition is ON. |
IMRC Solenoid (Intake Manifold Runner Control) | On Off | - | This parameter displays the engine control modules commanded state of the IMRC solenoid. |
IMRC Solenoid Circuit Status (Intake Manifold Runner Control) | Passed Failed Incompleted | - | This parameter displays the state of the intake manifold runner control (IMRC) circuit. The parameter displays Fault if the IMRC circuit is open, shorted to ground, or shorted to voltage. The parameter displays Indeterminate until the circuit has been commanded ON. This parameter may not change if the scan tool is used to command the IMRC solenoid ON. |
IMRC Solenoid Feedback Signal (Intake Manifold Runner Control) | - | % | |
Injection Time Cylinder 1 | - | ms | This parameter displays the amount of fuel injector ON time in Millie seconds as commanded by the engine control module. |
Injection Time Cylinder 2 | ms | ||
Injection Time Cylinder 3 | ms | ||
Injection Time Cylinder 4 | ms | ||
Injection Time Cylinder 5 | ms | ||
Injection Time Cylinder 6 | ms | ||
Injector 1 Disabled Due to Misfire | No Yes | - | This parameter displays the status of each of the Injector Disabled Due to Misfire. |
Injector 2 Disabled Due to Misfire | No Yes | - | |
Injector 3 Disabled Due to Misfire | No Yes | - | |
Injector 4 Disabled Due to Misfire | No Yes | - | |
Injector 5 Disabled Due to Misfire | No Yes | - | |
Injector 6 Disabled Due to Misfire | No Yes | - | |
Intake Air Temperature | - | °C | This parameter displays the temperature of the air entering the air induction system based on input to the control module from the intake air temperature (IAT) sensor. |
Knock Retard | - | °CA | This parameter indicates the amount of spark advance the control module removes from the ignition control (IC) spark advance in response to the signal from the knock sensors. |
Knock Retard Cylinder 1 | - | °CA | This parameter indicates how much ignition spark timing is being retarded due to all control systems monitored by the engine control module. |
Knock Retard Cylinder 2 | °CA | ||
Knock Retard Cylinder 3 | °CA | ||
Knock Retard Cylinder 4 | °CA | ||
Knock Retard Cylinder 5 | °CA | ||
Knock Retard Cylinder 6 | °CA | ||
Knock Sensor 1 Test Status | Passed Failed Incomplete | - | This parameter displays the status of each of the Knock sensors and circuits. |
Knock Sensor 2 Test Status | Passed Failed Incomplete | - | |
Knock Sensor Circuit Test Status | Passed Failed Incomplete | - | |
Loop Status B1S1 (Bank 1 Sensor 1) | Open Closed | - | This parameter displays the state of the fuel control system as commanded by the engine control module. Closed Loop operation indicates that the engine control module is controlling the fuel delivery based off the oxygen sensors input signal. In Open Loop operation the engine control module ignores the oxygen sensor input signal and bases the amount of fuel to be delivered on other sensor inputs. |
Loop Status B2S1 (Bank 2 Sensor 1) | Open Closed | ||
Malfunction Indicator (MI) | On Off | - | This parameter displays the commanded state of the malfunction indicator lamp (MIL) control circuit by the control module. |
Malfunction Indicator (MI) Circuit Status | OK Undefined Fault | - | This parameter displays the status of the Malfunction Indicator Circuit. |
Mass Air Flow | - | g/s | This parameter displays the measured quantity of air flowing into the engine during all operating conditions. |
Mass Air Flow Sensor | - | Hz | The scan tool displays in Hz. This parameter indicates the frequency signal sent from the MAF sensor to the engine control module. the scan tool will display a high value indicates a higher engine speed. The scan tool will display a low value at idle. |
Misfire Current Cyl. #1 | - | Counts | The scan tool will display in counts. This parameter indicates the number of cylinder firing events detected as possible misfires on each cylinder during the last 200 crankshaft revolutions as calculated by the engine control module. The scan tool will display a low number for a low number of cylinder misfire events. The scan tool will display a high number for a high number of cylinder misfire events. |
Misfire Current Cyl. #2 | |||
Misfire Current Cyl. #3 | |||
Misfire Current Cyl. #4 | |||
Misfire Current Cyl. #5 | |||
Misfire Current Cyl. #6 | |||
Misfire History Cyl. #1 | - | Counts | The scan tool displays in counts. This parameter displays the total level of cylinder misfires that have been calculated for each cylinder by the engine control module. This parameter will not update or show activity until a misfire DTC has become active. The misfire history counters will update every 200 cylinder firing events. |
Misfire History Cyl. #2 | |||
Misfire History Cyl. #3 | |||
Misfire History Cyl. #4 | |||
Misfire History Cyl. #5 | |||
Misfire History Cyl. #6 | |||
Number of Warm-Ups Since DTCs Cleared' | - | Counts | This parameter displays the Number Of Warm-ups Since DTCs Cleared. |
Oil Level | Normal Low Not Programmes | - | This parameter displays if the level of the engine oil is within range as determined by the engine control module from information received from the engine oil level switch. |
Power Enrichment | No Yes | - | Scan tool displays Yes or No. Yes displayed indicates that the engine control module has detected conditions appropriate to operate in Power Enrichment mode. The engine control module commands Power Enrichment mode when a large increase in throttle position and load is detected. While in Power Enrichment, the engine control module will increase the amount of fuel delivered by entering Open Loop and increasing the injector pulse width. |
Powertrain Immobiliser Status | Released Standby Immob. at Startup Immob. No Resp Immob. Neg Resp Immob. Wrong Resp Post Release Pre Release | - | This parameter displays the status of the Powertrain Immobiliser. |
Reduced Engine Power | Inactive Active | - | The scan tool displays Active or Inactive. The scan tool displays Active when the engine control module receives a signal from the throttle actuator control (TAC) module that a TAC system fault is occurring. The scan tool displays inactive when the engine is operating normally. |
Requested Torque | - | % | This parameter displays the calculated amount torque requested of the controller. |
Spark Advance | - | °CA | This parameter displays the amount of spark advance the engine control module is commanding on the ignition control circuits. The engine control module determines the desired advance. |
Start Up ECT (Engine Coolant Temperature) | - | °C | This parameter indicates the engine coolant temperature at start-up, as calculated by the engine control module based on the input from the engine coolant temperature sensor. The scan tool will display a higher value at higher engine start-up temperatures, and a lower value at lower start-up temperatures. |
Start Up IAT (Intake Air Temperature) | - | °C | Indicates the intake air temperature (IAT) at the time that the vehicle was started. Used to determine if the last start-up was a cold start. The scan tool range is -39 to +140°C (-38 to +284°F). This parameter indicates the ambient air temperature at start-up. |
Starter Relay | On Off | - | This parameter displays the control modules commanded state of the starter motor relay control circuit. |
Starter Relay Circuit Status | OK Undefined Status Fault | - | This parameter displays the status of the Starter Relay Circuit. |
System Power Mode | - Invalid Off Asleep Off Awake Unlock Accessory Run Crank RAP | - | This parameter displays the status of the System Power Mode. |
TAC Motor PWM Command (Throttle Actuator Control) | - | % | This parameter displays the percent of throttle opening as calculated by the control module using information from the TP sensor. |
Total Knock Retard | - | °CA | This parameter indicates how much ignition spark timing is being retarded due to all control systems monitored by the engine control module. The scan tool will display a high value during extreme conditions such as high temperatures and antilock braking. The scan tool will display a lower value during lighter driving conditions. |
Total Misfire | - | Counts | The scan tool range is 0-255 counts. This parameter indicates the total level of misfire that has been detected on each cylinder. The misfire history counters will not update or show any activity until a misfire or DTC P0300 has become active. The misfire history counter will update every 200 cylinder firing events. |
TP Sensor 1 (Throttle Position) | - | % | This parameter displays the angle of the throttle position (TP) sensor 1 in percent. This information is calculated by the engine control module using the signal from the throttle position sensor 1. The scan tool will display a low percentage when the throttle plates are closed. The scan tool will display a high percentage when the throttle plates are fully open. |
TP Sensor 1 (Throttle Position) | - | V | The scan tool displays Volts. The scan tool displays Volts when the ignition is ON. |
TP Sensor 1 Learned Lower Position (Throttle Position) | - | V | This parameter displays the learned minimum value of TP sensor 1 as recorded by the engine control module during the last learn procedure. |
TP Sensor 1-2 Correlation (Throttle Position) | OK Fault | - | This parameter displays the results of a engine control module test that compares signals from the throttle position (TP) sensors 1 and 2 . The scan tool will display Agree when the signal from TP sensor 1 corresponds with the signal from TP sensor 2. The scan tool will display Disagree when the signal from TP sensor 1 conflicts with the signal from TP sensor 2. |
TP Sensor 2 (Throttle Position) | - | % | This parameter displays the angle of the throttle position (TP) sensor 2 in percent. This information is calculated by the engine control module using the signal from the throttle position sensor 2. The scan tool will display a low percentage when the throttle plates are closed. The scan tool will display a high percentage when the throttle plates are fully open. |
TP Sensor 2 (Throttle Position) | - | V | The scan tool displays Volts. The scan tool displays Volts when the ignition is ON. |
TP Sensor 2 Learned Lower Position (Throttle Position) | - | V | The scan tool displays Volts. The scan tool displays Volts when the ignition is ON. |
Traction Control | Inactive Active | - | This parameter displays Active if the EBTCM is commanding traction control. |
Transmission Gear | P-N In Gear | - | This parameter indicates the current state of the gear select switch on the transmission/transaxle as calculated by the engine control module based on the TR switch. The scan tool status will switch from High to Low as different combinations are met. On the scan tool in Park, the PRNDL would read P and A will be Low, and B and C will be High. |
Vehicle Speed | - | km/h | This parameter indicates the vehicle speed calculated by the engine control module based on an input from the vehicle speed sensor (VSS). the scan tool will display a high value at higher vehicle speeds, and a low value at lower vehicle speeds. |
Vehicle Speed Circuit Status | Passed Failed Incomplete | - | This parameter displays the status of the Vehicle Speed Circuit. The scan tool will display OK, Incomplete, Short B+, Short Gnd/Open. The scan tool will display OK/Incomplete if the circuit is operating correctly. |
Volumetric Efficiency | - | % | This parameter displays the calculated volumetric efficiency of the engine as calculated by the engine control module. |
