GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Captiva Sport 🢒 Engine 🢒 Engine Controls and Fuel - 3.5L 🢒 Evaporative Emission Canister Purge Solenoid Valve Replacement

Removal Procedure

    Object Number: 1883868 Size: SH
  1. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.
  2. Disconnect the engine wiring harness electrical connector (1) from the evaporative emission (EVAP) canister purge solenoid (4).

    3. Object Number: 1885563 Size: SH
  3. Disconnect the chassis EVAP line quick connect fitting (3) from the EVAP canister purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.

    4. Object Number: 1775003 Size: SH
  4. Remove the EVAP canister purge solenoid bolt (1).
  5. Remove the EVAP canister purge solenoid (2) from the upper intake manifold.
  6. Remove and discard the EVAP canister purge solenoid O-ring seal (3).

Installation Procedure

    Object Number: 1775003 Size: SH
  1. Install a NEW EVAP canister purge solenoid O-ring seal (3) to the upper intake manifold.
  2. Install the EVAP canister purge solenoid (2) to the upper intake manifold.

    3. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the EVAP canister purge solenoid bolt (1).

    4. Tighten
    Tighten the bolt to 16 N·m (12 lb ft).


    Object Number: 1885563 Size: SH
  4. Connect the chassis EVAP line quick connect fitting (3) to the EVAP canister purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.

    5. Object Number: 1883868 Size: SH
  5. Connect the engine wiring harness electrical connector (1) to the EVAP canister purge solenoid (4).
  6. Install the intake manifold cover. Refer to Intake Manifold Cover Replacement.

Removal Procedure

    Object Number: 1883868 Size: SH
  1. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.
  2. Disconnect the engine wiring harness electrical connector (1) from the evaporative emission (EVAP) canister purge solenoid (4).

    3. Object Number: 1885563 Size: SH
  3. Disconnect the chassis EVAP line quick connect fitting (3) from the EVAP canister purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.

    4. Object Number: 1775003 Size: SH
  4. Remove the EVAP canister purge solenoid bolt (1).
  5. Remove the EVAP canister purge solenoid (2) from the upper intake manifold.
  6. Remove and discard the EVAP canister purge solenoid O-ring seal (3).

Installation Procedure

    Object Number: 1775003 Size: SH
  1. Install a NEW EVAP canister purge solenoid O-ring seal (3) to the upper intake manifold.
  2. Install the EVAP canister purge solenoid (2) to the upper intake manifold.

    3. Caution: Refer to Fastener Caution in the Preface section.

  3. Install the EVAP canister purge solenoid bolt (1).

    4. Tighten
    Tighten the bolt to 16 N·m (12 lb ft).


    Object Number: 1885563 Size: SH
  4. Connect the chassis EVAP line quick connect fitting (3) to the EVAP canister purge solenoid. Refer to Plastic Collar Quick Connect Fitting Service.

    5. Object Number: 1883868 Size: SH
  5. Connect the engine wiring harness electrical connector (1) to the EVAP canister purge solenoid (4).
  6. Install the intake manifold cover. Refer to Intake Manifold Cover Replacement.