Caution: Refer to Gasoline/Gasoline Vapors Caution in the Preface section.

Important: There are several types of Plastic Collar Fuel and Evaporative Emission Quick Connect Fittings used on this vehicle.

•	Bartholomew (1)

•	Q Release (2)

•	Squeeze to Release (3)

•	Sliding Retainer (4)

•	Push Down TI (5)

The following instructions apply to all types of Plastic Collar Quick Connect Fittings except where indicated.
1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief .

Caution: Refer to Safety Glasses Caution in the Preface section.

Notice: Refer to Fuel and Evaporative Emission Hose/Pipe Connection Cleaning Notice in the Preface section.




2. Using compressed air, blow any dirt or debris from around the connection.



3. This step applies to Bartholomew style connector ONLY. Squeeze the plastic quick connect fitting release tabs.



4. This step applies to Release Tab style connectors ONLY. Release the fitting by pushing the tab toward the other side of the slot in the fitting.



5. This step applies to the Squeeze to Release style connector ONLY. Squeeze where indicated by the arrow shown above on both sides of the plastic ring surrounding the quick connect fitting.



6. This step applies to the Sliding Retainer style connector ONLY. Release the fitting be pressing on one side of the release tab causing it to push in slightly. If the tab doesn't move try pressing the tab in from the opposite side. The tab will only move in one direction.



7. This step applies to the Push Down TI style connector ONLY. Release the fitting by pressing on the tab indicate by the arrow.

Caution: Refer to Relieving Fuel Pressure Caution in the Preface section.




8. Pull the connection apart.
9. Wipe off the male pipe end using a clean shop towel.
10. Inspect both ends of the fitting for dirt and burrs.
11. Clean or replace the components as required.

Caution: Refer to Fuel Pipe Fitting Caution in the Preface section.

1. Apply a few drops of clean engine oil to the male connection end.



2. Push both sides of the quick-connect fitting together in order to cause the retaining feature to snap into place.



3. Once installed, pull on both sides of the connection in order to make sure the connection is secure.

Warning: Refer to Gasoline/Gasoline Vapors Warning in the Preface section.

Note: There are several types of Plastic Collar Fuel and Evaporative Emission Quick Connect Fittings used on this vehicle.

•	Bartholomew (1)

•	Q Release (2)

•	Squeeze to Release (3)

•	Sliding Retainer (4)

•	Push Down TI (5)

The following instructions apply to all types of Plastic Collar Quick Connect Fittings except where indicated.
1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief.

Warning: Refer to Safety Glasses Warning in the Preface section.

Caution: Refer to Fuel and Evaporative Emission Hose/Pipe Connection Cleaning Caution in the Preface section.




2. Using compressed air, blow any dirt or debris from around the connection.



3. This step applies to Bartholomew style connector ONLY. Squeeze the plastic quick connect fitting release tabs.



4. This step applies to Release Tab style connectors ONLY. Release the fitting by pushing the tab toward the other side of the slot in the fitting.



5. This step applies to the Squeeze to Release style connector ONLY. Squeeze where indicated by the arrow shown above on both sides of the plastic ring surrounding the quick connect fitting.



6. This step applies to the Sliding Retainer style connector ONLY. Release the fitting be pressing on one side of the release tab causing it to push in slightly. If the tab doesn't move try pressing the tab in from the opposite side. The tab will only move in one direction.



7. This step applies to the Push Down TI style connector ONLY. Release the fitting by pressing on the tab indicate by the arrow.

Warning: Refer to Relieving Fuel Pressure Warning in the Preface section.




8. Pull the connection apart.
9. Wipe off the male pipe end using a clean shop towel.
10. Inspect both ends of the fitting for dirt and burrs.
11. Clean or replace the components as required.

Warning: Refer to Fuel Pipe Fitting Warning in the Preface section.

1. Apply a few drops of clean engine oil to the male connection end.



2. Push both sides of the quick-connect fitting together in order to cause the retaining feature to snap into place.



3. Once installed, pull on both sides of the connection in order to make sure the connection is secure.