Battery Replacement LAT

Caution: Do not tip the battery over a 45 degree angle or acid could spill causing serious personal injury.

1. Remove the generator battery control module cover. Refer to Generator Control Module Cover Replacement .
2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .



3. Remove the ECM bracket bolts (2), nuts (1) and ECM bracket.
4. Set the ECM assembly aside.



5. Loosen the positive battery cable terminal nut (1) and secure the battery positive cable (2) out of the way.



6. Remove the battery hold down nuts (1) and the battery hold down retainer bracket (2).
7. Remove the battery from the vehicle.

Caution: Do not tip the battery over a 45 degree angle or acid could spill causing serious personal injury.

1. Install the battery to the vehicle.

Notice: Refer to Fastener Notice in the Preface section.

2. Install the battery hold down nuts (1) and the battery hold down retainer bracket (2).

Tighten
Tighten the nut to 10 N·m (89 lb in).




3. Install the positive battery cable terminal nut (1).

Tighten
Tighten the nuts to 5 N·m (45 lb in).




4. Install the ECM bracket, bolts (2) and nuts (1).

Tighten
Tighten the nuts and bolts to 10 N·m (89 lb in).

5. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
6. Install the generator battery control module cover. Refer to Generator Control Module Cover Replacement .

Battery Replacement Without LAT

1. Disconnect the negative battery cable . Refer to Battery Negative Cable Disconnection and Connection



2. Depress the tab (1) retaining the engine control Module (2).
3. Slide the engine control module (2) in order to disengage the engine control module bracket from the battery upper cover (3).
4. Position the engine control module assembly (2) to the side. Do not disconnect the wiring harness.



5. Release the two tabs (2).
6. Remove the battery upper (1) cover from the battery lower cover (3).



7. Loosen the positive battery cable retaining nut (2).
8. Remove the positive battery cable from the battery (1).



9. Remove the battery retaining bolt (2) and retainer block (3).
10. Remove the battery (1) from the vehicle.

1. Position the battery (1) into the vehicle.

Notice: Refer to Fastener Notice in the Preface section.

2. Install the battery retaining bolt (2) and retainer block (3).

Tighten
Tighten the bolt to 10 N·m (89 lb in).




3. Install the positive battery cable to the battery (1).
4. Tighten the positive battery cable retaining nut (2).

Tighten
Tighten the nut 5 N·m (45 lb in).




5. Install the battery upper (1) cover to the battery lower cover (3).
6. Ensure that the two retaining tabs (2) are securely latched.



7. Slide the engine control module assembly (2) onto the battery upper cover (3).
8. Ensure that the tab (1) retaining the engine control Module (2) is securely latched.
9. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection



2. Depress the tab (1) retaining the engine control Module (2).
3. Slide the engine control module (2) in order to disengage the engine control module bracket from the battery upper cover (3).
4. Position the engine control module assembly (2) to the side. Do not disconnect the wiring harness.



5. Release the two tabs (2).
6. Remove the battery upper (1) cover from the battery lower cover (3).



7. Loosen the positive battery cable retaining nut (2).
8. Remove the positive battery cable from the battery (1).



9. Remove the battery retaining bolt (2) and retainer block (3).
10. Remove the battery (1) from the vehicle.

1. Position the battery (1) into the vehicle.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the battery retaining bolt (2) and retainer block (3) and tighten to 10 N·m (89 lb in).



3. Install the positive battery cable to the battery (1).
4. Tighten the positive battery cable retaining nut (2) to 5 N·m (45 lb in)..



5. Install the battery upper (1) cover to the battery lower cover (3).
6. Ensure that the two retaining tabs (2) are securely latched.



7. Slide the engine control module assembly (2) onto the battery upper cover (3).
8. Ensure that the tab (1) retaining the engine control Module (2) is securely latched.
9. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection