GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Captiva Sport 🢒 Engine 🢒 Engine Mechanical - 2.4L 🢒 Water Pump and Balance Shaft Chain and Tensioner Installation

    Object Number: 412415 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Important: If the balance shafts are not properly timed to the engine, the engine may vibrate and make noise.

  1. Install the upper balance shaft chain guide and bolts.

    2. Tighten
    Tighten the upper balance shaft chain guide bolts to 15 N·m (11 lb ft).


    Object Number: 412414 Size: SH
  2. Install the small balance shaft chain guide.
  3. Install the balance shaft chain guide bolts.

    4. Tighten
    Tighten the chain guide bolts to 15 N·m (11 lb ft).


    Object Number: 412413 Size: SH
  4. Install the adjustable balance shaft drive chain guide.
  5. Install the adjustable balance shaft drive chain guide bolts.

    6. Tighten
    Tighten the chain guide bolts to 10 N·m (89 lb in).


    Object Number: 412528 Size: SH
  6. Reset the timing chain tensioner by performing the following steps:
    7. 6.1. Turn the tensioner plunger 90 degrees in its bore and compress the plunger.
    6.2. Turn the tensioner back to the original 12 o'clock position and insert a paper clip through the hole in the plunger body and into the hole in the tensioner plunger.
  7. Install the timing chain tensioner.
  8. Install the chain tensioner bolts.

    9. Tighten
    Tighten the chain tensioner bolts to 10 N·m (89 lb in).

  9. Remove the paper clip from the balance shaft drive chain tensioner.

    Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 412415 Size: SH

    Note: If the balance shafts are not properly timed to the engine, the engine may vibrate and make noise.

  1. Install the upper balance shaft chain guide and bolts and tighten to 15 N·m  (11 lb ft).

    2. Object Number: 412414 Size: SH
  2. Install the small balance shaft chain guide.
  3. Install the balance shaft chain guide bolts and tighten to 15 N·m  (11 lb ft).

    4. Object Number: 412413 Size: SH
  4. Install the adjustable balance shaft drive chain guide.
  5. Install the adjustable balance shaft drive chain guide bolts and tighten to 10 N·m  (89 lb in).

    6. Object Number: 412528 Size: SH
  6. Reset the timing chain tensioner by performing the following steps:
    7. 6.1. Turn the tensioner plunger 90 degrees in its bore and compress the plunger.
    6.2. Turn the tensioner back to the original 12 o'clock position and insert a paper clip through the hole in the plunger body and into the hole in the tensioner plunger.
  7. Install the timing chain tensioner.
  8. Install the chain tensioner bolts and tighten to 10 N·m  (89 lb in).
  9. Remove the paper clip from the balance shaft drive chain tensioner.