GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Captiva Sport 🢒 Engine 🢒 Engine Mechanical - 2.8L, 3.0L, 3.2L, or 3.6L 🢒 Crankshaft Balancer Installation

Tools Required

    • EN 46106 Engine Flywheel Holding Tool
    • J 41998-B Crankshaft Balancer Installer
    • J 45059 Angle Meter

    Object Number: 945978 Size: SH
  1. The EN 46106 must be installed onto the flywheel.
  2. Use the J 41998-B , nut, bearing and washer to install the crankshaft balancer.

    3. Object Number: 1864550 Size: SH

    Important: Do not lubricate the crankshaft front oil seal or crankshaft balancer sealing surfaces. The crankshaft balancer is installed into a dry seal.

  3. Apply lubricant to the inside of the crankshaft balancer hub bore.

    4. Object Number: 1864551 Size: SH
  4. Place the crankshaft balancer in position on the crankshaft.
  5. Thread the J 41998-B in the crankshaft. Ensure you engage at least 10 threads of the J 41998-B before pressing the crankshaft balancer in place.
  6. Push the crankshaft balancer into position by tightening the nut on the J 41998-B until the large washer bottoms out on the crankshaft end.
  7. Remove the J 41998-B .

    8. Object Number: 1864410 Size: SH
  8. Install the crankshaft balancer bolt.

    9. Notice: Refer to Fastener Notice in the Preface section.

  9. Tighten the crankshaft balancer bolt.

    10. Tighten

    1. Tighten the crankshaft balancer bolt to 100 N·m (74 lb ft).
    2. Tighten the crankshaft balancer bolt an additional 150 degrees using the J 45059 .

    Object Number: 945978 Size: SH
  10. Remove the EN 46106 .

Special Tools

    • EN-46106 Engine Flywheel Holding Tool
    • J-41998-B Crankshaft Balancer Installer
    • J-45059 Angle Meter
        For equivalent regional tools, refer to Special Tools.

    Object Number: 945978 Size: SH
  1. The EN-46106 tool must be installed onto the flywheel.
  2. Use the J-41998-B installer , nut, bearing and washer to install the crankshaft balancer.

    3. Object Number: 1864550 Size: SH

    Note: Do not lubricate the crankshaft front oil seal or crankshaft balancer sealing surfaces. The crankshaft balancer is installed into a dry seal.

  3. Apply lubricant to the inside of the crankshaft balancer hub bore.

    4. Object Number: 1864551 Size: SH
  4. Place the crankshaft balancer in position on the crankshaft.
  5. Thread the J-41998-B installer in the crankshaft. Ensure you engage at least 10 threads of the J-41998-B installer before pressing the crankshaft balancer in place.
  6. Push the crankshaft balancer into position by tightening the nut on the J-41998-B installer until the large washer bottoms out on the crankshaft end.
  7. Remove the J-41998-B installer .

    8. Object Number: 1864410 Size: SH
  8. Install the crankshaft balancer bolt.

    9. Caution: Refer to Fastener Caution in the Preface section.

  9. Tighten the crankshaft balancer bolt to 100 N·m (74 lb ft) and an additional 150 degrees using the J-45059 meter .

    10. Object Number: 945978 Size: SH
  10. Remove the EN-46106 tool .