Brake Pressure Modulator Valve Bracket Replacement Without RPO LAT

1. Place the ignition switch in the OFF position.
2. Remove the underhood electrical center. Refer to Underhood Electrical Center or Junction Block Replacement.
3. Without draining the coolant or removing the hoses, remove and position aside the radiator surge tank. Refer to Radiator Surge Tank Replacement.



4. Remove the brake pressure modulator valve (BPMV) bolt (1).



5. Without disconnecting the brake pipe fittings, carefully lift the BPMV assembly (1) upward to release the mounting pins from the BPMV bracket insulators.

Do not pry on the accumulator caps on the underside of the BPMV.

6. Position the BPMV assembly aside and secure with heavy mechanics wire or equivalent.



7. Remove the 2 BPMV bracket bolts (1).



8. Remove the BPMV bracket nut (1) and the BPMV bracket.
9. Inspect the insulators for damage and replace, if necessary.

1. Install the BPMV bracket.
2. Loosely install the BPMV bracket nut (1).

Notice: Refer to Fastener Notice in the Preface section.




3. Install the 2 BPMV bracket bolts (1).

Tighten
Tighten the bolts to 10 N·m (89 lb in).

4. Tighten the BPMV bracket nut.

Tighten
Tighten the nut to 10 N·m (89 lb in).




5. Carefully position the BPMV assembly (1) to the BPMV bracket insulators.



6. Install the BPMV bolt (1).

Tighten
Tighten the bolt to 10 N·m (89 lb in).

7. Install the radiator surge tank. Refer to Radiator Surge Tank Replacement.
8. Install the underhood electrical center. Refer to Underhood Electrical Center or Junction Block Replacement.

Brake Pressure Modulator Valve Bracket Replacement With RPO LAT

1. Place the ignition switch in the OFF position.
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.



3. Remove the 2 brake pressure modulator valve (BPMV) bracket bolts (1).



4. Remove the BPMV bolt (1).



5. Without disconnecting the brake pipe fittings, carefully lift the BPMV assembly (1) upward to release the mounting pins from the BPMV bracket insulators.

Do not pry on the accumulator caps on the underside of the BPMV.

6. Position the BPMV assembly aside and secure with heavy mechanics wire or equivalent.
7. Inspect the insulators for damage and replace, if necessary.

1. Install the BPMV (1) to the bracket.

Notice: Refer to Fastener Notice in the Preface section.




2. Install the BPMV bolt (1).

Tighten
Tighten the bolt to 10 N·m (89 lb in).




3. Install the 2 BPMV bracket bolts (1).

Tighten
Tighten the bolts to 10 N·m (89 lb in).

4. Lower the vehicle.

Brake Pressure Modulator Valve Bracket Replacement Except Hybrid

1. Place the ignition switch in the OFF position.
2. Remove the underhood electrical center. Refer to Underhood Electrical Center or Junction Block Replacement.
3. Without draining the coolant or removing the hoses, remove and position aside the radiator surge tank. Refer to Radiator Surge Tank Replacement.



4. Remove the brake pressure modulator valve (BPMV) bolt (1).



5. Without disconnecting the brake pipe fittings, carefully lift the BPMV assembly (1) upward to release the mounting pins from the BPMV bracket insulators.

Do not pry on the accumulator caps on the underside of the BPMV.

6. Position the BPMV assembly aside and secure with heavy mechanics wire or equivalent.



7. Remove the 2 BPMV bracket bolts (1).



8. Remove the BPMV bracket nut (1) and the BPMV bracket.
9. Inspect the insulators for damage and replace, if necessary.

1. Install the BPMV bracket.
2. Loosely install the BPMV bracket nut (1).

Caution: Refer to Fastener Caution in the Preface section.




3. Install the 2 BPMV bracket bolts (1) and tighten to 10 N·m (89 lb in).
4. Tighten the BPMV bracket nut to 10 N·m (89 lb in).



5. Carefully position the BPMV assembly (1) to the BPMV bracket insulators.



6. Install the BPMV bolt (1) and tighten to 10 N·m (89 lb in).
7. Install the radiator surge tank. Refer to Radiator Surge Tank Replacement.
8. Install the underhood electrical center. Refer to Underhood Electrical Center or Junction Block Replacement.