DTC P0315 for Chevrolet Captiva Sport 2009
Diagnostic Instructions
DTC Descriptor
DTC P0315: Crankshaft Position (CKP) System Variation Not Learned
Circuit/System Description
The crankshaft position (CKP) system variation learn feature is used to calculate reference period errors caused by slight tolerance variations in the crankshaft, and the CKP sensor. The calculated error allows the engine control module (ECM) to accurately
compensate for reference period variations. This enhances the ability of the ECM to detect misfire events over a wider range of engine speed and load. The ECM stores the CKP system variation values after a learn procedure has been performed. If the actual CKP
variation is not within the CKP system variation compensating values stored in the ECM, DTC P0300 may set.
Conditions for Running the DTC
| • | This DTC runs continuously when the above condition is met. |
Conditions for Setting the DTC
The CKP system variation values are not stored in the ECM memory.
Action Taken When the DTC Sets
DTC P0315 is a Type A DTC.
Conditions for Clearing the MIL/DTC
DTC P0315 is a Type A DTC.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References
for scan tool information
Circuit/System Testing
Important: The CKP system variation learn procedure may have to be repeated up to 5 times before the procedure is learned.
Perform the CKP system variation learn procedure. Refer to
Crankshaft Position System Variation Learn
. The scan tool should display Learned this Ignition.
| ⇒ | If the CKP system variation learn procedure cannot be performed successfully, inspect for the following conditions: |
| • | Any worn crankshaft main bearings |
| • | A damaged or misaligned reluctor wheel |
| • | Excessive crankshaft runout |
| • | Interference in the signal circuit of the CKP sensor |
| • | The ignition switch is in the ON position until there is insufficient system voltage. |
| • | An ECM power disconnect with the ignition ON that may have erased the stored value and set DTC P0315 |
| • | Any debris between the CKP sensor and the reluctor wheel |
Diagnostic Instructions
DTC Descriptor
DTC P0315: Crankshaft Position (CKP) System Variation Not Learned
Circuit/System Description
The crankshaft position (CKP) system variation learn feature is used to calculate reference period errors caused by slight tolerance variations in the crankshaft, and the CKP sensor. The calculated error allows the engine control module (ECM) to accurately
compensate for reference period variations. This enhances the ability of the ECM to detect misfire events over a wider range of engine speed and load. The ECM stores the CKP system variation values after a learn procedure has been performed. If the actual CKP
variation is not within the CKP system variation compensating values stored in the ECM, DTC P0300 may set.
Conditions for Running the DTC
| • | This DTC runs continuously when the above condition is met. |
Conditions for Setting the DTC
The CKP system variation values are not stored in the ECM memory.
Action Taken When the DTC Sets
DTC P0315 is a Type A DTC.
Conditions for Clearing the MIL/DTC
DTC P0315 is a Type A DTC.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
Note: The CKP system variation learn procedure may have to be repeated up to 5 times before the procedure is learned.
Perform the CKP system variation learn procedure. Refer to
Crankshaft Position System Variation Learn. The scan tool should display Learned this Ignition.
| ⇒ | If the CKP system variation learn procedure cannot be performed successfully, inspect for the following conditions: |
| • | Any worn crankshaft main bearings |
| • | A damaged or misaligned reluctor wheel |
| • | Excessive crankshaft runout |
| • | Interference in the signal circuit of the CKP sensor |
| • | The ignition switch is in the ON position until there is insufficient system voltage. |
| • | An ECM power disconnect with the ignition ON that may have erased the stored value and set DTC P0315 |
| • | Any debris between the CKP sensor and the reluctor wheel |
