Notice: Always use the correct fastener in the proper location. When you replace a fastener, use ONLY the exact part number for that application.

1. Remove the air cleaner screws.
2. Remove the air cleaner cover.
3. Remove the air cleaner filter from air cleaner housing.
4. Inspect the air cleaner filter for dust, dirt and water. Replace if required, refer to Section 0B .

1. Install the air cleaner filter into the air cleaner housing.
2. Install the cover to air cleaner housing.
3. Install the air cleaner screws

Tighten
Air cleaner cover screws to 3 N·m (26 lb in)

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Remove the air cleaner outlet duct.

Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

2. Disconnect the battery cables and remove the battery.
3. Remove the relay center push in retainer.
4. Position the relay center away from the air cleaner assembly.
5. Remove the push in retainer from air cleaner assembly to the battery tray.
6. Remove the air cleaner assembly.

Important: Ensure that the slide pin is properly located into the bracket hole.

1. Slide the pin (part of air cleaner assembly) into the bracket hole on the left strut tower.

Important: Verify full engagement of the inlet onto the resonator neck and no contact of the air cleaner to the strut tower.

2. Position and install the air cleaner inlet over the resonator neck.
3. Install the push in retainer from the air cleaner to the battery tray.
4. Install the relay center and the push in retainer.
5. Install the battery and connect the battery cables.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

6. Connect the air cleaner outlet duct.

Tighten
Tighten the air cleaner outlet duct clamps to 5 N·m(44 lb In).

1. Remove the air cleaner outlet resonator mounting screws.
2. Disconnect the air cleaner outlet resonator clamp at throttle body.
3. Remove the air cleaner outlet duct from air cleaner outlet resonator and air cleaner assembly.
4. Disconnect the crankcase vent hose from the air cleaner outlet duct.
5. Remove the air cleaner outlet resonator.

Important: Be sure that the air cleaner outlet resonator seals to the throttle body.

1. Install the air cleaner outlet resonator to the throttle body.
2. Connect the crankcase vent hose to the air cleaner outlet duct.
3. Install the air cleaner outlet resonator mounting screws.

Tighten

•	Air cleaner outlet resonator mounting screws to 5-7 N·m 60-84 lb. In.).

•	Air cleaner outlet resonator clamp to 4-5 N·m 35-44 lb. in.).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

4. Install the air cleaner outlet duct to the air cleaner outlet resonator and the air cleaner assembly.

Tighten
Air cleaner outlet duct clamps to 4-5 N·m (35-44 lb. in.).

1. Remove the air cleaner outlet splash shield.
2. Remove the LH headlamp assembly retaining screws.
3. Remove the LH headlamp assembly.
4. Disconnect the LH headlamp electrical connector(s).
5. Remove the front air cleaner intake duct upper push in retainer (4).
6. Remove the resonator front push in retainer (1).
7. Remove the LF tire and wheel.
8. Remove the LF wheel house panel.
9. Remove the front air cleaner intake duct lower retaining screw.
10. Remove the front air cleaner intake duct through headlamp assembly opening.
11. Remove the resonator rear push in retainer and upper attaching bolt.
12. Remove the resonator assembly through wheel house opening (3).

1. Install the resonator assembly through the wheel house opening.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the resonator rear push in retainer and the upper attaching bolt.

Tighten
Tighten the Resonator upper attaching bolt to 7 N·m (61 lb in).

3. Install the front air cleaner intake duct through the headlamp assembly opening (3).
4. Install the front air cleaner intake duct lower retaining screw.
5. Install the LF wheel house panel.
6. Install the LF tire and wheel.
7. Lower the vehicle.
8. Install the resonator front push in retainer (1).
9. Install the front air cleaner intake duct upper push in retainer (4).
10. Install the LH headlamp electrical connector(s).
11. Install the headlamp assembly.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

12. Install the LH headlamp assembly retaining screws.

Tighten
Tighten the headlamp assembly retaining screws to 7 N·m (61 lb in).

13. Install the air cleaner outlet splash shield.