Circuit Description
The PCM supplies a 5V reference signal and a ground to the sensor. The TP sensor sends a voltage signal back to the PCM relative to the throttle plate opening. The voltage will vary from approximately 0.45Vat closed throttle, to over 4.5V at wide open throttle.
Conditions for Setting the DTC
| • | TP is stable ± 2 %. |
| • | MAP is less than 37 kPa. |
| • | DTC(s) P0107, P0108, P0122 not set. |
| • | TP angle is greater than the following specified percentages at the given RPM's. |
| - | TP angle is greater than 99 % at 800 RPM |
| - | TP angle is greater than 33 % at 1600 RPM |
| - | TP angle is greater than 55 % at 2400 RPM |
| - | TP angle is greater than 60 % at 3200 RPM |
| - | TP angle is greater than 79 % at 4000 RPM |
| - | TP angle is greater than 75 % at 4800 RPM |
| - | TP angle is greater than 99 % at 5600 RPM |
| - | TP angle is greater than 99 % at 6400 RPM. |
Action Taken When the DTC Sets
| • | The malfunction indicator lamp (MIL) will illuminate after two consecutive ignition cycles in which the diagnostic runs with the malfunction present. |
| • | The PCM will record the operating conditions at the time that the diagnostic fails. This information will store in the Freeze Frame and Failure Records buffers. |
| • | A history DTC stores. |
| • | The coolant fan turns ON. |
Conditions for Clearing the MIL/DTC
| • | The MIL will turn OFF after three consecutive ignition cycles in which the diagnostic runs without a fault. |
| • | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
| • | The MIL/DTCs can be cleared by using the scan tool. |
Diagnostic Aids
If a DTC P0121 cannot be duplicated, the information included in the Freeze Frame data can be useful. Use the scan tool DTC information data to determine the status of the DTC. If the DTC occurs intermittently, using the DTC P0121 Diagnostic table may help isolate the problem.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
-
The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data taken when the fault occurred. The information is then stored in the scan tool for later reference.
-
The TP sensor has an auto zeroing feature. If the voltage reading is between 0.2 to 0.9 volts, the PCM will assume the TP sensor is at a closed throttle position (0%). If the reading is out of the auto zeroing range at closed throttle look for a binding or damaged linkage.
-
In order for DTC P0121 to set with a short voltage in the TP signal circuit, the voltage must be minimal enough to not set a DTC P0123 and more than 0.5 V.
-
Replacement PCM's must be reprogrammed. Refer to the latest Techline information for programming procedures.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | Go to | |
Does the TP angle value increase steadily when the accelerator pedal is depressed to a greater than the specified value and decrease steadily when the pedal is released to less than the specified value? | 95% ± 2% | |||
3 |
Is the TP angle vs. RPM value greater than the specified value in the Conditions For Setting The DTC? | -- | ||
4 | Disconnect the TP sensor electrical connector. Is the TP sensor voltage less than the specified value? | 0.5V | ||
5 | Connect a test light between the 5V reference circuit and the TP sensor signal circuit at the TP sensor electrical connector. Is the TP sensor voltage greater than the specified value? | 4.5V | ||
Check the TP signal circuit for a short to voltage and repair as necessary. Was a repair necessary? | -- | |||
7 | Check the TP sensor ground circuit for a high resistance between the TP sensor and the PCM and repair as necessary. Was a repair necessary? | -- | ||
8 | Check the TP sensor signal circuit for high resistance between the TP sensor and the PCM and repair as necessary. Was a repair necessary? | -- | ||
9 | Check the TP sensor and the PCM electrical connectors for poor connection and repair as necessary. Was a repair necessary? | -- | ||
10 | Replace the TP sensor. Is the action complete? | -- | -- | |
Replace the PCM. Is the action complete? | -- | |||
12 |
Does the scan tool indicate that this diagnostic ran and passed? | -- | ||
13 | Check if any additional DTC's are set. Are any DTC's displayed that have not been diagnosed? | -- | Go to applicable DTC table | System OK |
