Accelerator Controls Accelerator Control Cable

1. Remove left sound insulator. Refer to Section 8C.
2. Remove release cable retainer from lever assembly.
3. Depress the cable tangs and push forward toward engine compartment.
4. Remove the air intake duct.
5. Remove the screws (1) to accelerator control splash shield.
6. Remove the shield (5).
7. Remove the cruise control cable if equipped.
8. Depress the tangs on cable through the cable bracket (3).
9. Remove the cable (2) from the cam.

1. Route cable through cable bracket (3).
2. Press cable upward through bracket.
3. Ensure tangs expand and properly seat.
4. Install the cruise control cable.
5. Install the accelerator control splash shield (5).
6. Install the screws (1) to shield.

Tighten
Tighten the screws to 8 N·m (71 lb in).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. Install the air intake duct.
8. Route cable through cowl.
9. Slip accelerator cable (2) through slot in rod and then install retainer in rod, being sure it is seated.

Important: Flexible components (hoses, wires, conduits, etc.) must not be routed within 50 mm (2.0 in) of moving parts of accelerator linkage outboard of support unless routing is positively controlled.

10. Check for correct opening and closing positions by operating accelerator pedal. Make sure that the throttle valve reaches wide-open throttle position. If it does not, inspect for damaged or bent brackets, levers, or other components; or, for poor carpet fit under the accelerator pedal.
11. Install the left sound insulator. Refer to Section 8C.

Accelerator Controls Accelerator Cable Bracket

1. Remove the accelerator cable splash shield attaching screws and the splash shield from the accelerator cable bracket.
2. Remove the accelerator, cruise and transmission cables, (If so equipped).
3. Remove the accelerator cable bracket attaching bolts/nut (1) (2) and the accelerator cable bracket (3).

1. Install the accelerator cable bracket (3) with attaching nuts/bolt (1) (2).

Notice: Align the accelerator bracket with the accelerator cam in order to prevent cable wear which could cause the cable to break.

2. Install the top bolt to bracket.
3. Install the bolt and nut to bracket.

Tighten

•	Tighten the top bolt first.

•	Tighten bolt and nuts to 25 N·m(18 lb ft).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Accelerator Controls Accelerator Pedal

1. Remove left sound insulator.
2. Remove the release cable (1) retainer from lever assembly.
3. Remove the nuts to cowl.
4. Remove the pedal assembly (2).

1. Install the pedal assembly (2) to cowl.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the nuts to cowl.

Tighten
Tighten the nuts to 30 N·m (25 lb ft).

3. Slip accelerator cable (1) through slot in rod and then install retainer in rod, being sure it is seated.
4. Install the left sound insulator.

Important: Flexible components (hoses, wires, conduits, etc.) must not be routed within 50 mm (2.0 in) of moving parts of accelerator linkage outboard of support unless routing is positively controlled.

5. Check for correct opening and closing positions by operating accelerator pedal. Make sure that the throttle valve reaches wide-open throttle position. If it does not, inspect for damaged or bent brackets, levers, or other components; or, for poor carpet in under the accelerator pedal.