GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2001 🢒 Cavalier 🢒 Engine 🢒 Engine Controls - 2.4L 🢒 DTC P0530

Circuit Description

The powertrain control module (PCM) monitors the high side refrigerant pressure via a A/C refrigerant pressure sensor. When the pressure is high the signal voltage is high. When the pressure is low the signal voltage is low. When pressure is high the PCM commands the cooling fans on. When pressure is too high or too low the PCM will not allow the A/C compressor clutch to engage.

Conditions for Running the DTC

The engine is running.

Conditions for Setting the DTC
    • The PCM detects the signal circuit is less than 5 counts (0.09 volt) or more than 250 counts (4.90 volts).
    • The condition exists for 15 seconds.

Action Taken When the DTC Sets
    • The PCM will not illuminate the Malfunction Indicator Lamp (MIL).
    • The PCM stores the failure records.
    • The A/C compressor clutch is disabled.

Conditions for Clearing the DTC
    • The DTC will become history if the PCM no longer detects a failure.
    • The history DTC will clear after 40 fault free ignition cycles.
    • The DTC can be cleared with a scan tool.

Test Description

The number(s) below refer to the step number(s) on the diagnostic table.

  1. Tests for the proper operation of the circuit in the low voltage range.

    2.

  2. Tests for the proper operation of the circuit in the high voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to ground.

    3.

  3. Tests for a short to voltage in the 5-volt reference circuit.

Step

Action

Value(s)

Yes

No

Schematic Reference: HVAC Schematics

1

Did you perform the HVAC Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - HVAC Systems - Manual

2

Important: The ambient air temperature must be above 3 degrees Celsius (38 degrees Fahrenheit).

  1. Turn OFF the engine.
  2. Inspect the A/C compressor for free rotation operation.
  3. Start the engine.
  4. Place the HVAC control module in the OFF position.

Does the A/C compressor operate?

--

Go to HVAC Compressor Clutch Does Not Disengage

Go to Step 3

3

Important: This step must be performed in an area with an ambient temperature that is greater than 0°C (32°F).

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the A/C High Side Pressure parameter in the powertrain control module Engine Data 2 list.

Does the scan tool indicate that the A/C High Side Pressure parameter is within the specified range?

0.2-3.76 V

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the A/C refrigerant pressure sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the A/C High Side Pressure parameter.

Does the scan tool indicate that the A/C High Side Pressure parameter is less than the specified value?

0.2 V

Go to Step 5

Go to Step 11

5

  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the A/C refrigerant pressure sensor and the signal circuit of the A/C refrigerant pressure sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the A/C High Side Pressure parameter.

Does the scan tool indicate that the A/C High Side Pressure parameter is greater than the specified value?

3.76 V

Go to Step 6

Go to Step 9

6
  1. Disconnect the fused jumper wire.
  2. Measure the voltage between the 5-volt reference circuit of the A/C refrigerant pressure sensor and the low reference circuit of the A/C refrigerant pressure sensor.

Does the voltage measure less than the specified value?

5.1 V

Go to Step 7

Go to Step 8

7
  1. Turn OFF the ignition.
  2. Disconnect the negative battery cable.
  3. Measure the resistance from the low reference circuit of the A/C refrigerant pressure sensor to a good ground.

Does the resistance measure less than the specified value.

5 ohms

Go to Step 13

Go to Step 12

8

Test the 5-volt reference circuit of the A/C refrigerant pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 14

9

Test the 5 volt reference circuit of the A/C refrigerant pressure sensor for a short to ground, a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 10

10

Test the signal circuit of the A/C refrigerant pressure sensor for a short to ground a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 14

11

Test the signal circuit of the A/C refrigerant pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 14

12
  1. Disconnect the powertrain control module.
  2. Test the low reference circuit of the A/C refrigerant pressure sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 14

13

Inspect for poor connections at the harness connector of the A/C refrigerant pressure sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 15

14

Inspect for poor connections at the harness connector of the powertrain control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 17

Go to Step 16

15

Replace the A/C refrigerant pressure sensor. Refer to Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement in Heating, Ventilation and Air Conditioning.

Did you complete the replacement?

--

Go to Step 17

--

16

Important: Perform the programming procedure for the powertrain control module.

Replace the powertrain control module. Refer to one of the following procedures:

    •  Powertrain Control Module Replacement in Engine Controls-2.2L
    •  Powertrain Control Module Replacement in Engine Controls-2.4L

Did you complete the replacement?

--

Go to Step 17

--

17
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 3

System OK