Circuit Description
The parklamps are controlled by the turn/headlamp switch. Positive battery voltage is supplied to the switch through the EXT LP fuse. When the turn/headlamp switch is placed in the park or head position, battery voltage is supplied to the park lamps. The body control module is also connected to the parklamp circuit to sense whether or not the parklamps turn on when the lowbeam or highbeam headlamps are turned on. The BCM also uses the parklamp battery positive voltage to power the instrument panel dimmer output circuit. If the BCM senses that the lowbeam or highbeam headlamps are on and the parklamp input is not active, DTC B2662 sets.
Conditions for Running the DTC
| • | The ignition switch is in the ON position. |
| • | The lowbeam or highbeam headlamps are on. |
Conditions for Setting the DTC
The parklamp input is inactive for 1 second.
Action Taken When the DTC Sets
DTC B2662 is stored in the BCM memory.
Conditions for Clearing the DTC
| • | The conditions for setting the DTC are no longer present. |
| • | A history DTC clears after 100 malfunction free ignition cycles. |
| • | The BCM receives the clear code command from the scan tool. |
Diagnostic Aids
| • | The low or highbeam headlamps must be on in order to set this DTC. |
| • | An open EXT LP fuse will set this code. |
| • | If the DTC is a history DTC, the problem may be intermittent. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Exterior Lights Schematics | |||
1 | Did you perform the Lighting System Diagnostic System Check? | Go to Step 2 | |
2 |
Does the scan tool display toggle between on and off? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 | Are the parklamps operating normally when the headlamp switch is turned on and then off? | Go to Step 4 | Go to Step 6 |
4 | Test the signal circuit of the turn/headlamp switch for an open between S216 and the BCM. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 5 |
5 | Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 9 |
6 | Test the battery positive voltage circuit of the turn/headlamp switch for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 7 |
7 | Test the parklamp signal circuit of the turn/headlamp switch for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 8 |
8 | Inspect for poor connections at the harness connector of the turn/headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 10 |
9 |
Important: Perform the set up procedure for the body control module. Replace the body control module. Refer to Body Control Module Replacement . Did you complete the replacement? | Go to Step 11 | -- |
10 | Replace the turn/headlamp switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column. Did you complete the replacement? | Go to Step 11 | -- |
11 |
Does the DTC reset? | Go to Step 2 | System OK |
