Cruise control is a speed control system that maintains
a desired vehicle speed under normal driving conditions. However, steep grades
may cause variations in the selected speeds. The electronic cruise control
system has the capability to CRUISE, COAST, RESUME SPEED, ACCELERATE, and
TAP-UP or TAP-DOWN.
The main parts of the cruise control system are:
• | The cruise control module assembly |
• | The function control switches |
• | The cruise control release switch |
• | The clutch pedal position switch (CPP), if equipped |
• | The stoplamp switch assembly |
• | The vehicle speed sensor |
The cruise control system uses the cruise control module assembly to
maintain the desired vehicle cruise speed and operation. The cruise control
module assembly has an electronic controller and an electric stepper motor
to vary the throttle in each different cruise control mode. The electric
controller monitors vehicle speed and operates the electric stepper motor.
The stepper motor operates in response to the electronic controller,
to maintain the desired cruise speed. The electric stepper motor moves a
strap that is attached to the cruise control cable which moves the throttle
linkage. The cruise control module assembly contains a low speed limit which
will prevent system engagement below a minimum speed of 40 km/h (25 mph).
The module assembly is not serviceable.
The operation of the electronic controller is controlled by the function
control switches located on the multifunction turn signal lever. The cruise
control functional control switches include the ON/OFF, SET/COAST and R/A
(resume/accelerate) switch. The switch assembly provides driver control
of the cruise control system.
The TCC/Brake switch and the stoplamp switch control both the cruise
control release signal and stoplamp signal. These signal circuits are used
to disengage the cruise control. The TCC/Brake and stoplamp switch assembles
are mounted on the brake pedal bracket. To disengage the system electrically
the driver presses the brake pedal. The speed of the vehicle at brake actuation
will be stored in the memory of the cruise module.
With cruise control, you can maintain a speed of about 40 km/h (25 mph)
or more without keeping your foot on the accelerator. When the driver turns
off the on/off switch, or the ignition switch, the cruise control turns
off. The vehicle speed stored in the memory of the cruise module will be
lost.
Ignition positive voltage is supplied from the cruise fuse,
to the cruise control module and cruise control switch. The cruise control
module is grounded to the chassis. When the cruise control ON/OFF switch
is on, ignition positive voltage is applied to the cruise on switch signal
circuit of the cruise control module. If the driver has not pressed the
brake pedal, ignition positive voltage is supplied through the cruise control
release circuit, to the cruise control release signal terminal of the cruise
control module. On vehicles equipped with a manual transmission, a clutch
switch is wired in series on this circuit and operates the same. When the
driver presses the brake pedal, battery positive voltage is supplied from
the stoplamp fuse, through the closed stoplamp switch to the stoplamp switch
signal terminal of the cruise control module. As this operation occurs,
ignition positive voltage is removed from the cruise release signal circuit.
If equipped, voltage is also removed from the cruise release signal circuit
when the clutch pedal is pressed. When the SET/COAST is pressed on the
control switch, ignition positive voltage is applied to the set/coast switch
signal terminal of the cruise control module. When pressing the R/A (resume/accelerate)
on the control switch, ignition positive voltage is applied to the resume/
accelerate switch signal terminal of the cruise control module.
The cruise control module receives a vehicle speed signal input from
the Powertrain Control Module (PCM). In operation, the voltage varies between
0 V and 5 V.
The cruise control module, cruise indicator control terminal, sends
a signal to the PCM when cruise is engaged. The cruise control module, cruise
cancel signal terminal, is a circuit used by the PCM to inhibit cruise
control when conditions inconsistent with cruise operation are present.
After the cruise control engage criteria has been met and the cruise
ON and Set/Coast have been commanded, the cruise control module sends a signal
to the PCM that the cruise control is engaged. The PCM then send a class
2 message to the instrument panel cluster (IPC) to illuminate the cruise
light, if equipped.
The PCM will inhibit cruise control:
• | When vehicle speed is less than 40 km/h (25 mph). |
• | When in PARK,REVERSE, NEUTRAL, or 1st gear. |
• | With high engine RPM (fuel cut-off) |
• | When vehicle speed is to high |
• | When an over or under charged battery voltage condition exists |
• | Antilock brake system/traction control system is active for more
than 2 seconds |
If the PCM determines that any of the cruise control inhibit conditions
are present, the PCM will disengage the cruise control. The PCM accomplishes
this by opening the cruise control inhibit signal circuit.