Circuit Description
The fuel rail temperature (FRT) sensor is a variable resistor that measures the temperature of the fuel in the CNG fuel rail. The powertrain control module (PCM) supplies 5 volts to the FRT signal circuit and supplies a ground to the low reference circuit. This DTC sets when the FRT signal voltage is above the normal operating range of the sensor.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
| • | The fuel rail temperature sensor voltage is more than 4.96 V. |
| • | The condition exists for more than 3 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Use the Temperature vs Resistance table in order to test the FRT sensor at various temperature levels in order to evaluate the possibility of a skewed sensor. A skewed sensor could result in a driveability condition. If the engine has sat overnight, the FRT sensor and the intake air temperature values should display within a few degrees. If the temperatures are not within 3°C (5°F), refer to Fuel Rail Temperature Sensor Output Voltage Versus Temperature Resistance . |
| • | For an intermittent condition, refer to Intermittent Conditions . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to voltage.
-
This step test the signal circuit of the FRT sensor. If the scan tool does not display 0 volts when the circuit is grounded, test for an open circuit between the PCM and the FRT sensor.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check Alternative Fuels - Engine Controls? | -- | Go to Step 2 | Go to Diagnostic System Check - Alternative Fuels (Engine Controls) |
2 |
Does the scan tool indicate that the FRT is near the specified value? | 5 V | Go to Step 4 | Go to Step 3 |
3 |
Does the DTC fail this ignition cycle? | -- | Go to Step 4 | Go to Diagnostic Aids |
Important: If the fuse opens, repair the short to voltage on the FRT signal circuit. Does the scan tool indicate that the FRT is at the specified value? | 0 V | Go to Step 8 | Go to Step 5 | |
Does the scan tool indicate that the FRT is at the specified value? | 0 V | Go to Step 7 | Go to Step 6 | |
6 | Test the signal circuit of the FTT sensor for an open circuit or for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems in the J Platform Service Manual. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
7 | Test the low reference circuit of the FTT sensor for an open circuit or for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems in the J Platform Service Manual. Did you find and correct the condition? | Go to Step 12 | Go to Step 9 | |
8 | Test for an intermittent and for a poor connection at the FTT sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems in the J Platform Service Manual. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 |
9 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems in the J Platform Service Manual. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 |
10 | Replace the FRT sensor. Refer to Fuel Temperature Sensor Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- |
11 | Replace the PCM. Refer to Powertrain Control Module Replacement in the J Platform Service Manual. Did you complete the replacement? | -- | Go to Step 12 | -- |
12 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 13 |
13 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | |
