REVISION TO SECTION 6E1 AND 6C1 IN SERVICE MANUAL
VEHICLES AFFECTED: 1984 'T' Cars with 1.6L Engine (Code C) and Lead Fuel Tolerant System (NM8)
This bulletin supercedes Section 6E1 (Pg. 32-36) and Section 6C1 (Pg. 4-8) which appear in the 1984 Canadian Passenger Car and Light Duty Truck Service Manual Supplement.
1. Choke Plate, Primary
2. Choke Shaft & Lever Assembly
3. Choke Housing Shaft & Lever Assembly
4. Choke Lever
5. Fast Idle, Adjustment Lever
6. Economizer Screw & Lockwasher
7. Choke Plate, Secondary
8. Choke Plate Screw
9. "E" Clip
10. Throttle Plate Screw
11. Spring
12. Retaining Ring Screw
13. Diaphragm Cover Screw & Lockwasher
14. Choke Housing Screw & Lockwasher
15. Fast Idle Adjustment Screw
16. Air Horn Screw & Lockwasher
17. Fast Idle Lever Screw & Lockwasher
18. Secondary Diaphragm Mounting Bolts
19. Pump Discharge Screw
20. Pump Cover Screw & Lockwasher
21. Choke Diaphragm Adjustment Screw
22. Idle Stop Screw
23. Pump Discharge Nozzle
24. Fuel Inlet Needle Seat Gasket
25. Pump Discharge Spring
26. Pump Discharge Ball
27. Choke Housing & Plugs Assembly
28. Pump Discharge Nozzle Gasket
29. Air Horn Gasket
30. Throttle Plate, Secondary
31. Throttle Plate, Primary
32. Throttle Shaft 7 Lever Assembly, Secondary
33. Secondary Diaphragm Case & Bracket Assembly
34. Throttle Lever Assembly, Primary
35. Bushing
36. Pump Cam
37. Washer
38. Lock Washer
39. Nut
40. Idle Adjusting Needle
41. Float Assembly
42. Fuel Inlet Needle & Seat Assembly
43. Fuel Inlet Fitting
44. Fuel Inlet Fitting Gasket
45. Main Metering Jet, Secondary
46. Main Metering Jet, Primary
47. Fast Idle Lever Bushing
48. Main Well Tube, Secondary
49. Main Well Tube, Primary
50. High Speed Bleed Restriction, Secondary
51. High Speed Bleed Restriciton, Primary
52. Power Valve Assembly
53. Power Valve Economizer Assembly
54. Choke Rod Seal
55. Primary Throttle Return Spring
56. Secondary Throttle Pickup Lever
57. Float Hinge Pin
58. Cover Screw
59. Idle Needle Limiter Cap
60. Pump Cover Assembly
61. Cover
62. Choke Diaphragm Cover Assembly
63. Fuel Inlet Filter Assembly
64. Pump Diaphragm Assembly
65. Diaphragm & Shaft Assembly
66. Spring Retainer (Choke)
67. Fuel Inlet Filter Spring
68. Idle Adjustment Needle Spring
69. Idle Stop Screw Spring
70. Fast Idle Adjustment Screw Spring
71. Diaphragm Return Spring
72. Pump Return Spring
73. Throttle Return Spring Primary
74. Fast Idle Cam Spring
75. Choke Shaft Nut
76. Thermostat Housing Retaining Ring
77. Thermostat Housing Assembly
78. Thermostat Ground Ring
79. Thermostat Housing
80. Fast Idle Cam & Hub Assembly
81. Choke Rod
82. Fast Idle Rod
83. Fast Idle Adjustment Lever Washer
84. Fast Idle Lever Spring Washer
85. Choke Shaft Nut Lockwasher
86. Choke Rod Retainer
General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.
