Circuit Description
The mass air flow (MAF) sensor is an air flow meter that measures the amount of air entering the engine. The powertrain control module (PCM) uses the MAF sensor frequency signal in order to provide the correct fuel delivery for a wide range of engine speeds and loads. A small quantity of air entering the engine indicates deceleration or idle. A large quantity of air entering the engine indicates an acceleration or high load situation. The MAF sensor has an ignition 1 voltage circuit, a ground circuit and a signal circuit. The PCM applies a voltage to the sensor on the signal circuit. The sensor uses the voltage in order to produce a frequency based on inlet air flow through the sensor bore. DTC P0103 will set if the PCM detects a frequency signal higher than the possible range of a normally operating sensor.
Conditions for Running the DTC
| • | The engine is running. |
| • | The engine run time is greater than 0.5 seconds. |
| • | The engine speed is at least 300 RPM. |
| • | The ignition 1 signal is greater than 8 volts. |
Conditions for Setting the DTC
The MAF sensor frequency signal is equal to or more than 13,000 Hertz.
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
Water entering the air intake system that reaches the MAF sensor could cause this diagnostic trouble code (DTC) to set. The water rapidly cools the hot sensing elements in the sensor causing a false indication of excessive air flow. Inspect the following areas for evidence of water intrusion:
| • | The secondary air injection (AIR) system |
| • | The air induction system |
A poor connection in the ignition positive voltage circuit of the MAF sensor can cause a DTC P0103 to set.
If the problem is intermittent, refer to Intermittent Conditions .
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for electromagnetic interference (EMI) on the signal circuit of the MAF sensor. A frequency reading with the MAF sensor disconnected indicates an EMI related fault or a poor connection. Disconnecting the MAF sensor may set additional related DTCs.
-
This step eliminates any conditions which can cause a DTC to set with a normally operating MAF sensor.
Step | Action | Values | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||||||
2 |
Does the DTC fail this ignition? | -- | Go to Step 3 | Go to Diagnostic Aids | ||||||||
Does the scan tool display the specified value? | 0 Hz | Go to Step 5 | Go to Step 4 | |||||||||
Inspect the MAF sensor harness for incorrect routing at the following locations:
Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 6 | |||||||||
5 | Inspect for poor connections at the harness connector of the MAF sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 7 | ||||||||
6 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 8 | ||||||||
7 | Replace the MAF/IAT sensor. Refer to Mass Airflow Sensor/Intake Air Temperature Sensor Replacement . Did you complete the replacement? | -- | Go to Step 9 | -- | ||||||||
8 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 9 | -- | ||||||||
9 |
Does the DTC run and pass? | -- | Go to Step 10 | Go to Step 2 | ||||||||
10 | Use a scan tool in order to observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |||||||||
