If the fuel supply system is not delivering enough fuel, or air is being drawn into the fuel injection system, driveability could be greatly effected or an Engine Cranks But Does Not Run symptom could exist. If another diagnosis indicates, or if the fuel supply system is suspected of not delivering enough fuel or drawing air, the following systems should be checked.

1. Install a scan tool.
2. Disconnect the pipe at the lift pump outlet fitting.
3. Install a hose at the lift pump outlet fitting and place a 1 liter (0.946 quart) container at the hose in order to collect fuel.
4. Use the scan tool in order to command the lift pump ON and measure the amount of fuel.

•	If more than 0.24 liter (½ pint) in 15 seconds, refer to Fuel Lift Pump Pressure Check below.

•	If less than 0.24 liter (½ pint) in 15 seconds, refer to Fuel Lift Pump Suction Line Check below.

1. Remove the fuel tank cap and repeat the Lift Pump Flow Check.

•	If the flow is more than 0.24 liter (½ pint) in 15 seconds, replace the defective fuel tank cap.

•	If the flow is less than 0.24 liter (½ pint) in 15 seconds, proceed to the next step.

2. Separate the lift pump suction line from the fuel sender.
3. Connect the suction line to a source of clean fuel by using an additional hose.
4. Repeat the Lift Pump Flow Check.

•	If the flow is more than 0.24 liter (½ pint) in 15 seconds, proceed to Fuel System Air Leak Check.

•	If the flow is less than 0.24 liter (½ pint) in 15 seconds, proceed to Step 5.

5. Check the lift pump suction line for a restriction.

•	If a restriction exists, repair the restriction and recheck lift pump flow.

•	If no restriction exists, replace the lift pump and recheck the lift pump flow. Refer to Fuel Pump Electrical Circuit Diagnosis .

6. Attach the lift pump suction line to the fuel sender.

1. Install a tee adapter at the injection pump.
2. Connect a pressure gauge with the dial indication of 0-103 kPa (0-15 psi) to the tee adapter.
3. Start the engine and measure the fuel pressure.

•	If the fuel pressure is a least 4 psi (27 kPa) proceed to Step 4.

•	If the pressure is less than 4  psi, refer to Fuel Pump Electrical Circuit Diagnosis before replacing the lift pump.

4. Remove the pressure gauge and the tee adapter.
5. Connect the inlet pipe.
6. Clean any fuel spillage.
7. Operate the engine and check for any fuel leaks.

1. Install a transparent hose between the filter outlet and the injection pump inlet.
2. Start and idle the engine, observing the fuel for air bubbles.

•	If air bubbles are not present, stop the engine and proceed to Step 7.

•	If air bubbles are present, stop the engine and proceed to Step 3.

3. Check the lift pump suction line for air leakage.

•	Disconnect the fuel pipe from the fuel sender.

•	Plug the fuel pipe.

•	Disconnect the fuel pipe from the lift pump.

•	Install a hand held vacuum pump with a gauge.

•	Apply vacuum to the fuel pipe and observe the gauge reading.

-	If the vacuum does not drop, connect the fuel pipe and proceed to Step 4.

-	If the vacuum drops, repair the air leak in the suction line and install the suction line pipe and the hose.

4. Check the fuel sender for air leakage.

•	Remove the fuel tank.

•	Remove the fuel sender from the fuel tank.

•	Remove the strainer and plug the bottom end of the pickup tube.

•	Apply a vacuum to the upper end of the pickup tube.

•	Observe the gauge reading.

-	If the vacuum does not drop (fuel inlet side of sender is OK), install the fuel sender and the fuel tank.

-	If the vacuum drops, replace the fuel sender, install the fuel tank, connect the fuel pipe and proceed to Step 5.

5. Start and run the engine.
6. Observe the fuel for air bubbles.

•	If air bubbles are present, stop the engine and recheck Steps 3 and 4.

•	If air bubbles are not present, stop the engine and proceed to Step 7.

7. Remove the transparent hose and connect the hose of the filter outlet to the injection pump inlet fitting.
8. Disconnect the return hose at the injection pump.
9. Install a transparent hose between the injection pump and the hose of the return line.
10. Start and run the engine.
11. Observe the fuel for air bubbles.

Important: Small amounts of bubbles present during snap acceleration is normal.

•	If air bubbles are present, replace the injection pump. Refer to Fuel Injection Pump Replacement .

•	If air bubbles are not present, proceed to Step 12.

12. Stop the engine.
13. Remove the transparent hose and attach the fuel return hose at the injection pump.
14. Clean any fuel spillage.
15. Run the engine to check for fuel leakage.

When the key is first turned ON without the engine running, the control module turns the fuel lift pump relay ON during glow plug cycle. This builds up fuel pressure quickly. If the engine is not started after the glow plug cycle, the control module shuts the fuel lift pump OFF and waits for engine RPM. As soon as the engine is cranked, the control module turns the relay ON and runs the fuel lift pump.

For the location of the fuel pump relay, refer to Engine Controls Component Views . For diagnosis of the lift pump electrical circuit, refer to Fuel Pump Electrical Circuit Diagnosis .