Circuit Description
The flow of transmission fluid starts in the transmission pan. It is then drawn through the filter and transmission case into the oil pump assembly. The oil pump assembly pressurizes the fluid, line pressure, which becomes the main supply line of fluid. This fluid is directed to various components and hydraulic circuits within the transmission. The pressure regulator valve receives this fluid and directs it to the converter clutch shift valve. The converter clutch shift valve directs hot fluid leaving the torque converter or regulated converter feed fluid, through the cooler line to the transmission oil cooler. The transmission oil cooler is located in the radiator. The vehicle may also be equipped with an auxiliary oil cooler. The cooled fluid, center lube, is returned to the transmission through the return cooler line and into center lube port of the transmission. The automatic transmission fluid temperature (TFT) sensor, senses the fluid temperature in the transmission pan.
If the powertrain control module (PCM) detects a high TFT for a long period of time, then DTC P0218 sets. DTC P0218 is a type C DTC.
Conditions for Running the DTC
| • | The system voltage is 10-18 volts. |
| • | No TFT sensor DTCs P0711, P0712 or P0713. |
| • | The engine is running for greater than 7 seconds. |
Conditions for Setting the DTC
The TFT is greater than 130°C (266°F) for more than 600 seconds (10 minutes).
Action Taken When the DTC Sets
| • | The PCM does not illuminate the malfunction indicator lamp (MIL). |
| • | The PCM freezes shift adapts from being updated. |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure Records. |
| • | The PCM stores DTC P0218 in PCM history. |
Conditions for Clearing the DTC
| • | A scan tool clears the DTC from PCM history. |
| • | The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without a non-emission related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Verify the customer driving habits, such as trailer towing. |
| • | The scan tool transmission fluid temperature (TFT) should rise steadily during warm-up cycles then stabilize. |
| • | DTC P0218 may set approximately 600 seconds (10 minutes) after DTC P0711 has set. Follow the diagnostic table for DTC P0711 before proceeding to the diagnostic table for DTC P0218. Repairing the condition that set DTC P0711 will likely eliminate DTC P0218. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Value(s) | Yes | No | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | Go to Step 2 | Go to Diagnostic System Check - Engine Controls in Engine Controls - 8.1L | ||||||||||||||||||||
2 |
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Failure Records from the PCM. Refer to Transmission Fluid Check . Was the fluid checking procedure performed? | -- | Go to Step 3 | Go to Transmission Fluid Check | ||||||||||||||||||||
Did you find and correct the condition? | -- | Go to Step 6 | Go to Step 4 | |||||||||||||||||||||
4 | Perform the Line Pressure Check Procedure. Refer to Line Pressure Check . Did you find and correct the condition? | -- | Go to Step 6 | Go to Step 5 | ||||||||||||||||||||
5 | Inspect the torque converter stator for damage. Refer to Torque Converter Diagnosis . Did you find and correct the condition? | -- | Go to Step 6 | |||||||||||||||||||||
6 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK | Go to Step 1 |
