Valve Rocker Arm Cover Replacement Left Side

1. Disconnect the negative battery cable. Refer to

   Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

   in General Information.
2. Remove the PCV valve and tube.
3. Remove the accessory drive belt. Refer to Drive Belt Replacement
4. Loosen the A/C compressor bracket bolts and slide forward. Refer to Air Conditioning Compressor Replacement in HVAC.
5. Remove the EGR tube. Refer to EGR Valve Replacement in Engine Controls.
6. Remove the spark plug wires. Refer to Spark Plug Wire Replacement in Engine Electrical.



7. Remove the valve rocker arm cover bolts.



8. Remove the valve rocker arm cover and gasket.
9. Clean all traces of old gasket from the valve rocker arm cover and cylinder head.
10. Inspect the valve rocker arm cover sealing surface for distortion and damage. Replace the valve rocker arm cover if necessary.

1. Install the valve rocker arm cover and a new gasket.



2. Install the valve rocker arm cover bolts.

Tighten
Tighten the bolts to 12 N·m (106 lb in).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the spark plug wires. Refer to Spark Plug Wire Replacement in Engine Electrical.
4. Install the air conditioning compressor and bracket. Refer to Air Conditioning Compressor Replacement in HVAC.
5. Install the PCV valve and tube.
6. Connective the negative battery cable. Refer to

   Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

   in General Information.

Valve Rocker Arm Cover Replacement Right Side

1. Disconnect the negative battery cable. Refer to

   Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

2. Remove the air cleaner box and the intake duct. Refer to Air Cleaner (Air Intake Duct) in Engine Controls.
3. Remove the spark plug wires. Refer to Spark Plug Wire Replacement in Engine Electrical.
4. Remove the vent tube.
5. Move the heater hoses aside.
6. Remove the wiring harness at the valve rocker arm cover, including the bracket.
7. Remove the oil level indicator tube bracket bolt. Refer to Oil Level Indicator and Tube Removal .



8. Remove the valve rocker arm cover bolts.



9. Remove the valve rocker arm cover and gasket.
10. Clean all traces of old gasket from the valve rocker arm cover and cylinder head.
11. Inspect the valve rocker arm cover sealing surface for distortion and damage. Replace the valve rocker arm cover if necessary.

1. Install the valve rocker arm cover and a new gasket.



2. Install the valve rocker arm cover bolts.

Tighten
Tighten the bolts to 12 N·m (106 lb in).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the oil level indicator tube bracket bolt. Refer to Oil Level Indicator and Tube Removal .
4. Install the spark plug wiring harness. Refer to Spark Plug Wire Replacement in Engine Electrical.
5. Install the air cleaner box and the intake duct. Refer to Air Cleaner (Air Intake Duct) in Engine Controls.
6. Connective the negative battery cable. Refer to

   Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

   in General Information.