GM Service Manual Online
For 1990-2009 cars only

Filler Tube Replacement Pickup

Removal Procedure


    Object Number: 300314  Size: SH

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable.
  2. Clean all the fuel pipe and hose connections and the surrounding areas before disconnection in order to avoid possible contamination of the fuel system.
  3. Remove the fuel filler cap.
  4. Drain the fuel below the level of the fuel filler hose. Refer to Fuel Tank Draining .

  5. Object Number: 300318  Size: SH
  6. Remove the fuel fill pipe housing to fuel fill pipe bolts.
  7. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  8. Object Number: 420291  Size: SH
  9. Disconnect the fuel fill pipe ground strap.

  10. Object Number: 300178  Size: SH
  11. Disconnect the rear axle vent hose from the retainer on the fuel fill pipe.
  12. Loosen the fuel vent hose to fuel tank clamp (4).
  13. Disconnect the fuel fill and vent hoses (3) from the fuel tank.
  14. Remove the fuel fill and vent pipe and hose assembly.
  15. Cap the open end of the fuel tank.

Installation Procedure


    Object Number: 300178  Size: SH
  1. Uncap the fuel tank.
  2. Install the fuel fill and vent pipe and hose assembly to the fuel tank.
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Align the fuel fill pipe to the fuel fill pipe housing.
  5. Tighten
    Tighten the vent hose clamp (4) to 2.5 N·m (22 lb in)


    Object Number: 420291  Size: SH
  6. Connect the fuel fill pipe ground strap.
  7. Tighten
    Tighten the fuel fill pipe ground strap bolt to 9 N·m (80 lb in)

  8. Connect the rear axle vent hose to the retainer on the fuel fill pipe
  9. Lower the vehicle.

  10. Object Number: 300318  Size: SH
  11. Install the fuel fill pipe housing to the fuel fill pipe bolts.
  12. Tighten
    Tighten the fuel fill pipe housing to fuel fill pipe bolts to 2.3 N·m (20 lb in)


    Object Number: 300314  Size: SH
  13. Refill the fuel system.
  14. Install the fuel filler cap.
  15. Connect the negative battery cable.

Filler Tube Replacement Utility with Single Side Tank

Removal Procedure


    Object Number: 300314  Size: SH

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable.
  2. Clean all the fuel pipe and hose connections and the surrounding areas before disconnection in order to avoid possible contamination of the fuel system.
  3. Remove the fuel filler cap.
  4. Drain the fuel below the level of the fuel filler hose. Refer to Fuel Tank Draining .

  5. Object Number: 300318  Size: SH
  6. Remove the fuel fill pipe housing to fuel fill pipe bolts.
  7. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  8. Object Number: 561119  Size: SH
  9. Disconnect the fuel fill pipe ground strap (3).

  10. Object Number: 570590  Size: SH
  11. Disconnect the rear axle vent hose from the retainer on the fuel fill pipe, (if applicable).
  12. Loosen the fuel vent hose to fuel tank clamp (1).
  13. Loosen the fuel fill hose to fuel tank clamp (11).
  14. Disconnect the fuel fill pipe bracket bolt (3).
  15. Disconnect the fuel fill and vent hoses from the fuel tank.
  16. Remove the fuel fill and vent pipe and hose assembly.
  17. Cap the open end of the fuel tank.

Installation Procedure


    Object Number: 570590  Size: SH
  1. Uncap the fuel tank.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the fuel fill and vent pipe hose assembly to the fuel tank.
  4. Tighten
    Tighten the vent hose clamp (1) and the fuel fill pipe clamp (11), to 2.5 N·m (22 lb in)

  5. Install the fuel fill pipe bracket bolt (3) and tighten to 12.0 N·m(106 lb in)

  6. Object Number: 561119  Size: SH
  7. Connect the fuel fill pipe ground strap (3).
  8. Tighten
    Tighten the fuel fill pipe ground strap bolt (1) to 9 N·m (80 lb in)

  9. Connect the rear axle vent hose to the retainer on the fuel fill pipe, if applicable.
  10. Lower the vehicle.

  11. Object Number: 300318  Size: SH
  12. Install the fuel fill pipe housing to the fuel fill pipe bolts.
  13. Tighten
    Tighten the fuel fill pipe housing to fuel fill pipe bolts to 2.3 N·m (20 lb in)


    Object Number: 300314  Size: SH
  14. Refill the fuel system.
  15. Install the fuel filler cap.
  16. Connect the negative battery cable.

Filler Tube Replacement Utility with Dual Tanks

Removal Procedure


    Object Number: 300314  Size: SH

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable.
  2. Clean all the fuel pipe and hose connections and the surrounding areas before disconnection in order to avoid possible contamination of the fuel system.
  3. Remove the fuel filler cap.
  4. Drain the fuel below the level of the fuel filler hose. Refer to Fuel Tank Draining .

  5. Object Number: 300318  Size: SH
  6. Remove the fuel fill pipe housing to fuel fill pipe bolts.
  7. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  8. Object Number: 561111  Size: SH
  9. Disconnect the fuel fill pipe ground strap.

  10. Object Number: 569704  Size: SH
  11. Disconnect the rear axle vent hose from the retainer on the fuel fill pipe.
  12. Loosen the fuel vent hose (3) to fill tube clamp (2).

  13. Object Number: 569669  Size: SH
  14. Loosen the fuel fill hose to fuel tank clamp (2).
  15. Disconnect the fuel fill hose from the fuel tank.
  16. Remove the fuel fill hose assembly.
  17. Cap the open end of the fuel tank.

Installation Procedure


    Object Number: 569669  Size: SH
  1. Uncap the fuel tank.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the fuel fill hose assembly to the fuel tank.
  4. Tighten
    Tighten the fuel fill pipe clamp (2), to 2.5 N·m (22 lb in)


    Object Number: 569704  Size: SH
  5. Connect the fuel fill vent hose (3) to the fill tube.
  6. Tighten
    Tighten the vent hose clamp (2), to 2.5 N·m (22 lb in)


    Object Number: 561111  Size: SH
  7. Connect the fuel fill pipe ground strap.
  8. Tighten
    Tighten the fuel fill pipe ground strap bolt to 9 N·m (80 lb in)

  9. Connect the rear axle vent hose to the retainer on the fuel fill pipe.
  10. Lower the vehicle.

  11. Object Number: 300318  Size: SH
  12. Install the fuel fill pipe housing to the fuel fill pipe bolts.
  13. Tighten
    Tighten the fuel fill pipe housing to fuel fill pipe bolts to 2.3 N·m (20 lb in)


    Object Number: 300314  Size: SH
  14. Refill the fuel system.
  15. Install the fuel filler cap.
  16. Connect the negative battery cable.