GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 25025 Guide Pin

Removal Procedure


    Object Number: 477683  Size: SH
  1. Remove the 3rd and 4th clutch accumulator housing bolts (1).
  2. Remove the 3rd and 4th clutch accumulator housing (8).
  3. Remove the accumulator housing gasket (6). The accumulator housing gasket may be stuck to the spacer plate (5).
  4. Remove the 3rd clutch accumulator piston spring (7).
  5. Remove the 4th clutch accumulator piston spring (2).
  6. Remove the control valve body spacer plate (5).
  7. Remove the control valve assembly to spacer plate gasket (4) from the spacer plate (5).

Third and Forth Clutch Accumulator Disassembly


    Object Number: 477676  Size: SH

    Important: Apply low pressure compressed air to the hole at the top of the accumulator housing to assist with the piston removal.

  1. Remove the 3rd clutch accumulator piston (2).
  2. Remove the 3rd clutch accumulator piston seals (1 and 3 ) .

  3. Object Number: 477680  Size: SH
  4. Remove the 4th clutch accumulator piston pin retainer ring (5).
  5. Remove the 4th clutch accumulator piston (4) and pin (2) from the accumulator housing (1).
  6. Remove the 4th clutch accumulator piston pin (2) from the accumulator housing (1).
  7. Remove the 4th clutch accumulator piston seal (3) from the accumulator housing (1).

Third and Forth Clutch Accumulator Assembly


    Object Number: 477676  Size: SH
  1. Install the 3rd clutch accumulator piston inner (3) and outer (1) seals. Lubricate the 3rd clutch accumulator piston seals (1 and 3) with DEXRON® VI automatic transmission fluid.
  2. Install the 3rd clutch accumulator piston (2).

  3. Object Number: 477680  Size: SH
  4. Install the 4th clutch accumulator piston seal (3). Lubricate the 4th clutch accumulator piston seal (3) with DEXRON® VI automatic transmission fluid.
  5. Assemble the 4th clutch accumulator piston pin (2) with the 4th clutch accumulator piston (4).
  6. Install the 4th clutch accumulator piston assembly into the accumulator housing (1).
  7. Install the 4th clutch accumulator piston pin retainer ring (5) onto the 4th clutch accumulator piston pin (2).

Installation Procedure


    Object Number: 477811  Size: SH
  1. Install the J 25025 into the control valve body bolt hole where the manual shaft detent roller and spring assembly is mounted.
  2. Install the control valve body gasket (2) onto the accumulator housing (1).
  3. Install the control valve body spacer plate (3) onto the valve body gasket (2).

  4. Object Number: 477816  Size: SH
  5. Install the third and fourth clutch accumulator housing gasket (3).
  6. Install the third clutch accumulator piston spring (1). This spring is the longer of the two springs.
  7. Install the fourth clutch accumulator piston spring (4).
  8. Install the third and fourth clutch accumulator housing assembly (5) onto the control valve body assembly (2).
  9. Install the six accumulator housing bolts (6). Start the bolts finger tight and work towards the opposite end.
  10. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 477819  Size: SH
  11. Tighten the accumulator housing bolts in the order shown.
  12. Tighten
    Tighten the accumulator housing bolts to 11 N·m (97 lb in).

  13. Remove the J 25025-5.
  14. Important: It is recommended that transmission adaptive pressure (TAP) information be reset.

    Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.

  15. Reset the TAP values. Refer to Adapt Function .