GM Service Manual Online
For 1990-2009 cars only

Rack Piston and Worm Shaft Replacement - Off Vehicle 670 Gear

Tools Required

    • J 21552 Rack Piston Arbor
    • J 8947 Rack Piston Teflon Ring Compressor

Disassembly Procedure


    Object Number: 412388  Size: SH
  1. Remove the pitman shaft and side cover assembly. Refer to Steering Gear Pitman Shaft and Housing Cover Replacement - Off Vehicle .
  2. Remove the pitman seals and bearing. Refer to Steering Gear Pitman Shaft Seal and Bearing Replacement - Off Vehicle .
  3. Remove the stub shaft housing assembly. Refer to Stub Shaft Housing Replacement .
  4. Turn the stub shaft counterclockwise until the rack piston (1) begins to come out of the steering gear housing.
  5. Insert J 21552 into the bore of the rack piston (2).
  6. Hold J 21552 tightly against the worm shaft while turning the stub shaft counterclockwise. Turning the stub shaft forces the rack piston (1) onto J 21552 . The rack piston balls remain in place.

  7. Object Number: 412388  Size: SH
  8. Remove J 21552 from the rack piston (1).

  9. Object Number: 412389  Size: SH
  10. Remove the teflon ring (2) from the steering gear housing (1).
  11. Remove the O-ring seal (3) from the steering gear housing (1).
  12. Clean all of the disassembled parts.
  13. Inspect all of the disassembled parts.
  14. Replace the parts if necessary.

Assembly Procedure


    Object Number: 412389  Size: SH
  1. Lubricate the following items with power steering fluid while installing to the rack piston (4):
  2. 1.1. The O-ring seal (3)
    1.2. The teflon ring (2)

    Object Number: 412388  Size: SH
  3. Insert J 21552 into the bore of the rack piston while turning the worm shaft counterclockwise.
  4. The turning of the worm shaft forces the rack piston onto J 21552 . The rack piston balls remain in place.
  5. Install the rack piston (1) to the worm shaft from using J 8947 to compress the seals.
  6. Install the stub shaft housing assembly. Refer to Stub Shaft Housing Replacement .
  7. Refer to Steering Gear Pitman Shaft Seal and Bearing Replacement - Off Vehicle to install the pitman seals and bearings.
  8. Refer to Steering Gear Pitman Shaft and Housing Cover Replacement - Off Vehicle to install the pitman shaft and side cover assembly.
  9. Adjust the steering gear.

Rack Piston and Worm Shaft Replacement - Off Vehicle 700 Gear

Tools Required

    • J 21552 Rack Piston Arbor
    • J 8947 Rack Piston Teflon Ring Compressor

Disassembly Procedure


    Object Number: 322017  Size: SH

    Important: Do not remove the needle bearing when removing the Pitman shaft arm and its components.

  1. Remove the Pitman shaft seals and bearing. Refer to Steering Gear Pitman Shaft Seal and Bearing Replacement - Off Vehicle .
  2. Remove the housing end plug. Refer to Steering Gear Housing Plug Replacement - Off Vehicle .
  3. Turn the stub shaft counterclockwise until the rack piston (2) begins to come out of the steering gear housing (3).
  4. Remove the rack piston plug (1).
  5. Insert J 21552 into the bore of the rack piston (2).
  6. Hold J 21552 tightly against the worm shaft while turning the stub shaft counterclockwise. Turning the stub shaft forces the rack piston (2) onto J 21552 . The rack piston balls remain in place.

  7. Object Number: 322087  Size: SH
  8. Remove the following items as an assembly from the steering gear housing (9):
  9. • The rack piston (4)
    • The rack piston screws (8), clamp (7), ball guide (6) and balls (5)
    • J 21552
  10. Remove the spool valve assembly. Refer to Steering Gear Valve Replacement - Off Vehicle .
  11. Remove the worm shaft (14).
  12. Remove the thrust bearing (12) and the flat races (11, 13).
  13. Important: When removing J 21552 , watch for falling piston balls (5) from inside the rack piston (4).

  14. Remove J 21552 from the rack piston (4).
  15. Remove the rack piston balls (5).
  16. Remove the following items from the rack piston (4):
  17. 13.1. The screws (8)
    13.2. The clamp (7)
    13.3. The ball guide (6)
    13.4. The remaining rack piston balls (5) in the ball guide (6)
  18. Remove the teflon ring (2).
  19. Remove the O-ring seal (3).
  20. Clean all of the disassembled parts.
  21. Inspect all of the disassembled parts for wear.
  22. Replace the parts if necessary.

Assembly Procedure


    Object Number: 322018  Size: SH
  1. Install the O-ring seal (3) and the teflon ring (2).
  2. Lubricate both parts with power steering fluid.
  3. Install the worm shaft (14) to the rack piston (4) outside of the steering gear housing (9).
  4. Fully seat the worm shaft to the rack piston.


    Object Number: 322019  Size: SH
  5. Align the worm shaft spiral groove with the rack piston ball return guide hole (1).
  6. Caution: In order to avoid injury and/or component damage, install all of the rack piston balls into the rack piston. Install the rack piston balls in the correct order. If you do not correctly install all of the rack piston balls, the steering gear may not operate or may wear out quickly.

  7. Lubricate the rack piston balls with power steering fluid.
  8. Insert the rack piston balls through the ball return guide hole (1) while turning worm shaft (2) counterclockwise in order to install the rack piston balls into the rack piston. Install the black and the silver rack piston balls alternately into the rack piston and the ball guide to maintain the rack piston to the worm shaft preload.

  9. Object Number: 322022  Size: SH
  10. Install the remaining rack piston balls (3) into the ball guide (1) using grease at each end (2) to retain the rack piston balls (3).

  11. Object Number: 740395  Size: SH
  12. Install the ball guide (3) to the rack piston (2).
  13. Install the ball guide clamp (4).
  14. Notice: Refer to Fastener Notice in the Preface section.

  15. Install the screws (5).
  16. Tighten
    Tighten the screws (5) to 6 N·m (53 lb in).

  17. Insert J 21552 into the bore of the rack piston while turning the worm shaft counterclockwise. The turning of the worm shaft forces the rack piston onto J 21552 . The rack piston balls remain in place.

  18. Object Number: 322025  Size: SH
  19. Install the flat races (2, 4) and the thrust bearing (3) onto the worm shaft (1).

  20. Object Number: 322026  Size: SH
  21. Install the worm shaft (4) to the steering gear housing (3).
  22. Important: Do not adjust the worm shaft until all components are installed onto the steering gear housing.

  23. Install the spool valve. Refer to Steering Gear Valve Replacement - Off Vehicle .
  24. Install the rack piston (2) to the worm (4) from J 21552 using J 8947 to compress the seals.
  25. Hold J 21552 tightly against the worm shaft (4).
  26. Turn the stub shaft clockwise until the rack piston (2) is seated on the worm shaft (4).
  27. Remove J 21552 from the rack piston (1).
  28. Install the rack piston plug (1).
  29. Tighten
    Tighten the rack piston plug to 150 N·m (111 lb ft).

  30. Install the housing end plug. Refer to Steering Gear Housing Plug Replacement - Off Vehicle .
  31. Important: Do not adjust the Pitman shaft until all components are installed onto the steering gear housing.

  32. Install the Pitman shaft seals and bearing. Refer to Steering Gear Pitman Shaft Seal and Bearing Replacement - Off Vehicle .
  33. To adjust the steering gear; refer to one of the following procedures:
  34. •  Steering Gear Worm Gear Thrust Bearing Preload Adjustment - Off Vehicle
    •  Steering Gear Pitman Shaft Over-Center Preload Adjustment - Off Vehicle