GM Service Manual Online
For 1990-2009 cars only

Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle Floor Shift


    Object Number: 415287  Size: SH
  1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Important: Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.

  3. Screw the 2 pan head tapping screws (1) into the turn signal and multifunction assembly (2).
  4. Tighten

    • Tighten the top pan head tapping screw (1) to 3 N·m (30 lb in).
    • Tighten the side pan head tapping screw (3) to 7N·m (62 lb in).

    Object Number: 306234  Size: SH
  5. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly into the bulkhead connector (1).

  6. Object Number: 415293  Size: SH
  7. Reconnect the turn signal and multifunction switch assembly connector to the inflatable restraint steering wheel module coil connector.
  8. Important: The abrasion sleeve must be installed back onto the steering column wire harness assembly. The electronic lock module assembly wires and connector must be hanging out of the middle of the abrasion sleeve.

  9. Attach the wire harness assembly (1) to the wire restraint clip (2).
  10. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
  11. Enable the inflatable restraint steering wheel module. Refer to Enabling the SIR System .

Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle Column Shift


    Object Number: 415287  Size: SH
  1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Important: Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.

  3. Screw the 2 pan head tapping screws (1) into the turn signal and multifunction assembly (2).
  4. Tighten
    Tighten the 2 pan head tapping screws to 7 N·m (62 lb in).


    Object Number: 306234  Size: SH
  5. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly into the bulkhead connector (1).

  6. Object Number: 415293  Size: SH
  7. Reconnect the turn signal and multifunction switch assembly connector to the inflatable restraint steering wheel module coil connector.
  8. Attach the wire harness assembly (1) to the steering column with new wire harness strap (2).
  9. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .

Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle Export


    Object Number: 415287  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Important: Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.

  1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.
  2. Screw the 2 pan head tapping screws (1) into the turn signal and multifunction assembly (2).

    Tighten
    Tighten the 2 pan head tapping screws to 7 N·m (62 lb in).


    Object Number: 306234  Size: SH
  3. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly into the bulkhead connector (1).

  4. Object Number: 415293  Size: SH
  5. Reconnect the turn signal and multifunction switch assembly connector to the inflatable restraint steering wheel module coil connector.
  6. Attach the wire harness assembly (1) to the steering column with wire harness strap (2).
  7. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .