Seat Belt Buckle and Latch Replacement - No. 3 Rear Tahoe/Yukon

Caution: To avoid personal injury to the occupants of the vehicle, observe the following precautions:

1. Remove the seat from the vehicle. Refer to Rear Bench Seat Replacement in Seats.
2. Manually rotate the center latch to the latched position to release the seat back.
3. Remove the latch cover.
4. Remove the latch mounting bolt attaching the retractor bolt anchor to the cushion frame.
5. Remove the seat back. Refer to Rear Seat Back Replacement in Seats.



6. Remove the head rests. Refer to Rear Seat Head Restraint Replacement in Seats.
7. Remove the seat back trim.
8. Remove the retractor mounting bolt.
9. Separate the bottom cushion trim J-strip.
10. Remove the handle mounting bolts.
11. Remove the seatbelt anchor bolt cover.
12. Remove the floor anchor bolt.
13. Remove the buckle attaching bolts.
14. Remove the buckle and latch from the vehicle.

1. Install the buckle and latch to the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the buckle attaching bolts.

Tighten
Tighten to 55 N·m (40 lb ft).

3. Install the handle mounting bolts.

Tighten
Tighten to 55 N·m (40 lb ft).

4. Connect the bottom cushion trim J-trim.
5. Install the retractor mounting bolt.

Tighten
Tighten to 55 N·m (40 lb ft).

6. Install the floor anchor bolt.

Tighten
Tighten to 55 N·m (41 lb ft).

7. Install the seat belt anchor bolt cover.



8. Install the seat back trim.
9. Install the headrests. Refer to Rear Seat Head Restraint Replacement in Seats.
10. Install the seat back. Refer to Rear Seat Back Replacement in Seats.
11. Install the latch mounting bolt attaching the retractor bolt anchor to the cushion frame.

Tighten
Tighten to 55 N·m (40 lb ft).

12. Install the latch cover.
13. Manually rotate the center latch to the un-latched position to secure the seat back.
14. Install the seat to the vehicle. Refer to Rear Bench Seat Replacement in Seats.

Seat Belt Buckle and Latch Replacement - No. 3 Rear Suburban/Yukon XL

Caution: To avoid personal injury to the occupants of the vehicle, observe the following precautions:

1. Remove the seat from the vehicle. Refer to Rear Bench Seat Replacement in Seats.
2. Manually rotate the center latch to the latched position to release the seat back.
3. Remove the latch cover.
4. Remove the latch mounting bolt attaching the retractor bolt anchor to the cushion frame.
5. Remove the seat back. Refer to Rear Seat Back Replacement in Seats.



6. Remove the head rests. Refer to Rear Seat Head Restraint Replacement in Seats.
7. Remove the seat back trim.
8. Remove the retractor mounting bolt.
9. Separate the bottom cushion trim J-strip.
10. Remove the handle mounting bolts.
11. Remove the seatbelt anchor bolt cover.
12. Remove the floor anchor bolt.
13. Remove the buckle attaching bolts.
14. Remove the buckle and latch from the vehicle.

1. Install the buckle and latch to the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the buckle attaching bolts.

Tighten
Tighten to 55 N·m (40 lb ft).

3. Install the handle mounting bolts.

Tighten
Tighten to 55 N·m (40 lb ft).

4. Connect the bottom cushion trim J-strip.
5. Install the retractor mounting bolt.

Tighten
Tighten to 55 N·m (40 lb ft).

6. Install the floor anchor bolt.

Tighten
Tighten to 55 N·m (41 lb ft).

7. Install the seat belt anchor bolt cover.



8. Install the seat back trim.
9. Install the headrests. Refer to Rear Seat Head Restraint Replacement in Seats.
10. Install the seat back. Refer to Rear Seat Back Replacement in Seats.
11. Install the latch mounting bolt attaching the retractor bolt anchor to the cushion frame.

Tighten
Tighten to 55 N·m (40 lb ft).

12. Install the latch cover.
13. Manually rotate the center latch to the un-latched position to secure the seat back.
14. Install the seat to the vehicle. Refer to Rear Bench Seat Replacement in Seats.