Seat Belt Buckle and Latch Replacement - No. 2 Rear Tahoe/Yukon

Caution: To avoid personal injury to the occupants of the vehicle, observe the following precautions:

1. Remove the door sill plate. Refer to Door Sill Plate Replacement in Interior Trim.
2. Remove the lower anchor bolt from bodyside panel.
3. Remove the third-pillar trim panel. Refer to Third Pillar Trim Replacement in Interior Trim.
4. Route the belt through trim panel.



5. Remove the bolt from the upper guide.
6. Remove the bolt from the retractor.
7. Remove the seatbelt anchor bolt cover.
8. Remove the floor anchor bolt.
9. Remove the assembly from the vehicle.

1. Install the assembly to vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt to the retractor.

Tighten
Tighten to 55 N·m (41 lb ft).

3. Install the bolt to the upper guide.

Tighten
Tighten to 55 N·m (41 lb ft).




4. Route the belt through trim panel.
5. Install the third-pillar trim panel. Refer to Third Pillar Trim Replacement in Interior Trim.
6. Install the lower anchor bolt to bodyside panel.

Tighten
Tighten to 55 N·m (41 lb ft).

7. Install the floor anchor bolt.

Tighten
Tighten to 55 N·m (41 lb ft).

8. Install the seat belt anchor bolt cover.
9. Install the door sill plate. Refer to Door Sill Plate Replacement in Interior Trim.

Seat Belt Buckle and Latch Replacement - No. 2 Rear Suburban/Yukon XL

Caution: To avoid personal injury to the occupants of the vehicle, observe the following precautions:

1. Remove the door sill plate. Refer to Door Sill Plate Replacement in Interior Trim.
2. Remove the seatbelt anchor bolt cover.
3. Remove the floor anchor bolt.



4. Remove the third-pillar trim panel. Refer to Third Pillar Trim Replacement in Interior Trim.
5. Route the belt through trim panel.
6. Remove the lower guide.
7. Remove the bolt from the upper guide.
8. Remove the bolt from the retractor.
9. Remove the assembly from the vehicle.

1. Install the assembly to the vehicle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt to the retractor.

Tighten
Tighten to 55 N·m (41 lb ft).

3. Install the bolt to the upper guide.

Tighten
Tighten to 55 N·m (41 lb ft).




4. Snap lower guide into place.
5. Route the belt through trim panel.
6. Install the third-pillar trim panel. Refer to Third Pillar Trim Replacement in Interior Trim.
7. Install the floor anchor bolt.

Tighten
Tighten to 55 N·m (41 lb ft).

8. Install the seat belt anchor bolt cover.
9. Install the door sill plate. Refer to Door Sill Plate Replacement in Interior Trim.