Electronic Column Lock Module - Assemble - Off Vehicle Floor shift Export
Assembly Procedure
- Install the lock bolt spring (3) into the steering column housing assembly (5).
- Position the cutout in the lock bolt assembly (4) at the 6 o'clock position.
- Install the lock bolt assembly (4) into the steering column housing assembly (5).
- Push the lock bolt assembly (4) into the steering column housing assembly (5) until the lock bolt assembly (4) is flush with the steering column housing assembly (5).
- Align the electronic lock module assembly (2) with the steering column housing assembly (5).
- Screw the 3 pan head tapping screws (1) into the electronic lock module assembly (2).
- Slide the ignition and key alarm switch assembly (3) into the electronic lock module assembly (1).
- Install the key alarm connector (1) onto the electronic lock module assembly (2) in the following way:
- Install the turn signal cancel cam, bearing thrust washer. Refer to Turn Signal Cancel Cam and Bearing Thrust Washer - Assemble - Off Vehicle .
Install the electronic lock module assembly (2) onto the steering column housing assembly (5).
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Tighten
Tighten the 3 pan head tapping screws to 7 N·m (62 lb in).
| 8.1. | Push the key alarm connector (1) into the electronic lock module assembly (2). |
| 8.2. | Rotate the key alarm connector 90 (1) degrees so that the key alarm connector locks into place. |
| 8.3. | Install the passkey connector into the electronic lock module assembly (2). |
Electronic Column Lock Module - Assemble - Off Vehicle Column shift Export
- Install the lock bolt spring (3) into the steering column housing assembly (5).
- Position the cutout in the lock bolt assembly (4) at the 6 o'clock position.
- Install the electronic lock bolt assembly (4) into the steering column housing assembly (5).
- Push the electronic lock bolt assembly (4) into the steering column housing assembly (5) until the lock bolt assembly is flush with the steering column housing assembly (5).
- Align the electronic lock module assembly (2) with the steering column housing assembly (5).
- Screw the 3 pan head tapping screws (1) into the electronic lock module assembly (2).
- Slide the ignition and key alarm switch assembly (3) into the electronic lock module assembly (1).
- Push the key alarm connector (1) into the electronic lock module assembly (2).
- Rotate the key alarm connector 90 degrees so that the key alarm connector locks into place.
- Install the passkey connector into the electronic lock module assembly (2).
- Place steering column lock cylinder set into the OFF position.
- Place the shift lever clevis into the PARK position.
- Press the locking tab on the end of the park lock cable assembly (1) into the slot in the electronic lock module assembly.
- Install the turn signal cancel cam, bearing thrust washer. Refer to Turn Signal Cancel Cam and Bearing Thrust Washer - Assemble - Off Vehicle .
Install the electronic lock module assembly (2) onto the steering column housing assembly (5).
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Tighten
Tighten the 3 pan head tapping screws to 7N·m (62 lb in).
