Tools Required

1. Apply masking tape to the area around the window in order to protect the painted surfaces from damage and to protect the headliner.
2. Remove the rear view mirror. Refer to Inside Rearview Mirror Replacement .
3. Remove the antenna mast.
4. Remove the windshield wiper arms. Refer to Windshield Wiper Arm Replacement .
5. Remove the cowl air inlet grill panel. Refer to Air Inlet Grille Panel Replacement in Body Front End.

Caution: If broken glass falls into the defroster outlets, it can be blown into the passenger compartment and cause personal injury.

6. Cover the defroster grille outlets and protect the headliner as needed.
7. Remove the door sealing weatherstrip from the upper pinchweld flange.




Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.

8. Reposition the front door weather-strips in order to access the reveal moldings.
9. Remove the reveal moldings.




Important: The windshield reveal molding fills the cavities between the body and windshield and can not be reused if stretched or damaged.

10. Remove the upper windshield molding by cutting the molding with a utility knife.




Important: Keep the cutting edge of the tool against the windshield when removing the windshield. This will allow the urethane adhesive to be separated from the windshield. Leave a base of urethane on the pinchweld flange. The only suitable lubrication is clear water.

11. Remove the sides and the top of the windshield from the urethane adhesive using a J 24402-A or J 39032 in order to remove the windshield.



12. Remove the bottom of the windshield from the urethane adhesive using a long utility knife or similar tool. Keep the cutting edge of the utility knife against the glass.



13. Remove the windshield from the vehicle with the aid of an assistant.
14. Inspect the following components for the causes of a broken windshield:

•	The flange of the windshield opening

•	The windshield reveal molding

•	The windshield

15. Inspect for any of the following problems in order to help prevent future breakage of the windshield:

•

High weld

•	Solder spots

•	Hardened spot weld sealer

•	Any other obstruction or irregularity in the pinchweld flange.

Important: If corrosion of the pinchweld flange is present, or if sheet metal repairs or replacements are required, the pinchweld flange must be refinished in order to restore the bonding area strength. If paint repairs are required, mask the flange bonding area prior to applying the color coat in order to provide a clean primer only surface. Materials such as BASF DE17®, DuPont  2610®, Sherwin-Williams PSE 4600 and NP70® and Martin-Semour 5120 and 5130® products are approved for this application.

16. After repairing the opening as indicated, perform the following steps:

16.1.

Inspect the condition of the windshield opening and the adhesive bead to determine which installation method should be used. Refer to Short Method Description or Extended Method Description for guidelines.

16.2.

Remove no more of the urethane adhesive from the pinchweld than necessary in order to maintain the original shape. This will ensure the proper clearance between the windshield and the pinchweld flange.

16.3.

Remove all traces of broken glass from the outer cowl panel, seats, floor and defroster ducts.

16.4.

Clean around the edge of the inside surface of the windshield with a 50/50 mixture of isopropyl alcohol and water by volume on a dampened lint free cloth.

Caution: When replacing stationary windows, use Urethane Adhesive Kit GM P/N 12346392 (Canadian P/N 10952983), or a urethane adhesive system meeting GM Specification GM3651G, to maintain original installation integrity. Failure to use the urethane adhesive kit will result in poor retention of the window which may allow unrestrained occupants to be ejected from the vehicle resulting in personal injury.

After repairing the opening as indicated, perform the following:

1. Shake the pinchweld primer (black #3) for at least one minute.




Caution: Failure to prep the area prior to the application of primer may cause insufficient bonding of urethane adhesive. Insufficient bonding of urethane adhesive may allow unrestrained occupants to be ejected from the vehicle resulting in personal injury.

2. Use a new dauber to apply the pinchweld primer (black #3) to the surface (1) of the bonding area.
3. Allow the primer to dry for approximately 10 minutes. Ensure that all nicks and scratches are covered.



4. If using extended method, install the spacers and the VIN plate filler strip.



5. Install the reveal molding to the edge of the windshield. If the original reveal molding is damaged it must be replaced.
6. Install a new acoustic strip if needed.



7. With the aid of an assistant, dry fit the windshield in the opening in order to determine the correct way to position the windshield in the opening.



8. Use masking tape (1) in order to mark the location of the windshield in the opening.
9. Slit the masking tape at the top edge of the windshield.
10. With the aid of assistant and using suction cups remove the windshield from the opening.
11. Place the windshield inside up on a clean, protected surface.
12. If the original windshield is being reused remove all but a thin film of the existing urethane adhesive from the windshield surface by using a clean utility knife or razor blade scraper.
13. Clean around the edge of the inside surface of the windshield with a 50/50 mixture of isopropyl alcohol and water by volume on a dampened lint free cloth.

Important: Do not remove all traces of the adhesive. Remove all mounds or loose pieces of urethane adhesive.

14. If the extended method is being used remove all but approximately 2 mm (3/64 in) of the existing bead of adhesive from the pinchweld flange.
15. Shake the pinchweld primer (black #3) for at least one minute.
16. Use a new dauber to apply the primer to the surface of the pinchweld flange.
17. Allow the pinchweld primer to dry for approximately 10  minutes.




Important: Use care when applying prep (clear #1) on the windshield. This primer dries almost instantly, and may stain the viewing area of the windshield if not applied evenly.

18. Use a new dauber in order to apply glass prep (clear #3) to the area approximately 10 mm to l6 mm (3/8 in to 5/8 in). around the entire perimeter of the window inner surface.
19. Apply a second coat of the glass prep number (clear #1) to the same area of the glass.
20. Wipe the glass primed area immediately with a clean lint free cloth.
21. Shake the glass primer (black #2) for at least one minute.



22. Use a new dauber in order to apply the glass primer (black #2) to the same areas (2) that glass prep (clear #1) was applied.

The glass primer (black #2) is good up to 8 hours after applying it to the glass. The primed surface of the glass must be kept clean.

23. Allow the glass primer to dry for approximately 10 minutes.



24. If using the short method, cut the tip of the applicator nozzle in order to provide a bead of 6.0 mm (1/4 in).
25. If using the extended method, cut the applicator nozzle in order to provide a bead of 12.7 mm (1/2 in) wide and 12.7 mm (1/2 in ) high.



26. Use a cartridge type caulking gun to apply a smooth, continuous bead of urethane adhesive.
27. When using the short method, apply the urethane adhesive to the existing bead of urethane adhesive on the body.



28. When using the extended method, use the edge of the windshield window or the inside edge of the reveal molding as a guide for the nozzle in order to apply the urethane adhesive (1) to the inner surface of the windshield window (3).

If applying urethane adhesive to the inside edge of the windshield reveal molding (1) use the windshield reveal molding as a guide for the nozzle.




29. With the aid of an assistant, use the suction cups in order to install the windshield window into the opening.



30. Align the tape (1) lines on the windshield and the body.
31. Press the windshield firmly into place.
32. Tape the windshield to the body in order to minimize movement until the urethane adhesive cures.
33. Clean any excess urethane adhesive from the body.




Important: Do not direct a hard stream of high pressure water to the freshly applied urethane adhesive.

34. Use a soft spray of warm water in order to immediately water test the windshield window.
35. Inspect the windshield for leaks.
36. If any leaks are found, use a plastic paddle in order to apply extra urethane adhesive at the leak point.
37. Retest the windshield for leaks.
38. The following conditions must be maintained to properly cure the urethane:
39. Allow the vehicle to remain at room temperature (21°C or 70°F) at 30 percent relative humidity.

Caution: At least 24 hours are required for complete curing of repair material. The repair area should not be physically distrubed until after that time. Insufficient curing of urethane adhesive may allow unrestrained occupants to be ejected from the vehicle resulting in personal injury.

39.1.

Allow a minimum of 6 hours for the moisture curing urethane adhesive.

39.2.

Allow a minimum of 1 hour to 1 1/2 hours for the chemical curing urethane adhesive.

39.3.

Partially lower a door window in order to prevent pressure buildups when closing doors before the urethane adhesive cures.

39.4.

Do not drive the vehicle until the urethane adhesive is fully cured. Refer to the above curing times.

39.5.

Do not use compressed air in order to dry the urethane adhesive.

1. Install the reveal moldings.
2. Install the front door weather-strips.
3. Install the cowl air inlet grill panel. Refer to Air Inlet Grille Panel Replacement in Body Front End.
4. Install the windshield wiper arms. Refer to Windshield Wiper Arm Replacement .
5. Install the antenna mast.
6. Install the rear view mirror. Refer to Inside Rearview Mirror Replacement .

Caution: If broken glass falls into the defroster outlets, it can be blown into the passenger compartment and cause personal injury.

7. Remove the protective coverings and tape from the vehicle and the headliner.