GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2003 🢒 Chevy C Silverado - 2WD 🢒 Engine 🢒 Engine Controls - 6.6L 🢒 Fuel Hose Replacement - Fuel Feed Block to Schrader Valve

Removal Procedure

    Object Number: 877275 Size: SH
  1. Drain the cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  3. Remove the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement .
  4. Loosen the charged air cooler outlet duct clamp (1).

    5. Important: Do not use a screwdriver or other tool to pry the hose loose. The hose can be torn or damaged. Loosen the hose by twisting.

  5. Remove the charged air cooler outlet duct.

    6. Object Number: 877281 Size: SH
  6. Loosen the charged air cooler inlet duct to turbocharger clamp (1).
  7. Remove the charged air cooler inlet duct from the turbocharger.
  8. Remove the engine wiring harness. Refer to Engine Wiring Harness Assembly Replacement .

    9. Object Number: 755184 Size: SH
  9. Remove the schrader valve nuts (1) and bracket (2).

    10. Object Number: 791989 Size: SH
  10. Reposition the fuel hose clamps.
  11. Remove the fuel hose (1) from the fuel feed block.
  12. Remove the schrader valve and fuel hose from the engine.
  13. Remove the fuel hose from valve.

Installation Procedure

    Object Number: 791989 Size: SH
  1. Install the fuel hose to the valve.
  2. Install the schrader valve and fuel hose to engine.
  3. Install the fuel hose (1) to fuel feed block.
  4. Reposition the fuel hose clamps.

    5. Object Number: 755184 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  5. Install the schrader valve bracket (2) and nuts (1) .

    6. Tighten
    Tighten the nuts to 20 N·m (15 lb ft).

  6. Install the engine wiring harness. Refer to Engine Wiring Harness Assembly Replacement .

    7. Object Number: 877281 Size: SH
  7. Install the charged air cooler inlet duct to the turbocharger.
  8. Align the mark on the duct (2) with the mark on the turbocharger.
  9. Position the clamp (1) as shown for proper clearance.

    10. Tighten
    Tighten the clamp to 6 N·m (53 lb in).


    Object Number: 877275 Size: SH
  10. Install the charged air cooler outlet duct to the intake.
  11. Align the mark on the duct (3) with the mark on the intake.
  12. Position the clamp (1) as shown for proper clearance.

    13. Tighten
    Tighten the clamp to 6 N·m (53 lb in).

  13. Install the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement .
  14. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  15. Fill the cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.