Engine Mechanical Specifications. Chevrolet Chevy G Van 1996

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1996 🢒 Chevy G Van 🢒 Engine 🢒 Engine Mechanical - 7.4L 🢒 Engine Mechanical Specifications

Engine Mechanical Specifications General

Application	Metric	English
General Data
Engine Type	V-8
Displacement	7.4L (454 CID)
RPO (VIN Code)	L29 (J)
Bore	107.95 mm	4.25 in
Stroke	101.6 mm	4.00 in
Compression Ratio	9.0:1
Firing Order	1-8-4-3-6-5-7-2
Spark Plug Gap	0.8890 mm	0.035 in
Oil Pressure (Minimum)Oil pressure should be taken at operating temperature.	68.65 kPa @ 600 RPM 172.37 kPa @ 2000 RPM	10 psi @ 600 RPM 25 psi @ 2000 RPM
Oil Filter Torque	16 N·m	12 lb ft
Oil Filter System	Full Flow
Oil Pump Type	Gear Driven

Engine Mechanical Specifications Unit Repair

Application	Metric	English
General Data
Engine Type	V-8
Displacement	7.4L	454 CID
RPO (VIN Code)	L29 (J)
Bore	107.95 mm	4.25 in
Stroke	101.6 mm	4.00 in
Compression Ratio	9.0:1
Firing Order	1-8-4-3-6-5-7-2
Spark Plug Gap	0.8890 mm	0.035 in
Oil Pressure (Minimum)	68.65 kPa @ 600 RPM 172.37 kPa @ 2000 RPM	10 psi @ 600 RPM 25 psi @ 2000 RPM
Oil Filter Torque	16 N·m	12 lb ft
Oil Filter System	Full Flow
Oil Pump Type	Gear Driven
Cylinder Bore
Diameter	107.950-107.968 mm	4.2500-4.2507 in
Out Of Round Production	0.0254 mm (Maximum)	0.001 in (Maximum)
Out Of Round Service	0.051 mm (Maximum)	0.002 in (Maximum)
Taper Production Thrust Side	0.0127 mm (Maximum)	0.0005 in (Maximum)
Taper Production Relief Side	0.0254 mm (Maximum)	0.001 in (Maximum)
Taper Service	0.0254 mm (Maximum)	0.001 in (Maximum)
Piston
Clearance Production	0.0457-0.0762 mm	0.0018-0.0030 in
Clearance Service Limit	0.0457-0.219 mm	0.0018-0.0048 in
Piston Ring Compression
Top Groove Production Clearance	0.031-0.074 mm	0.0012-0.0029 in
Second Groove Production Clearance	0.031-0.074 mm	0.0012-0.0029 in
Service Limit Groove Clearance	0.0991-0.305 mm	0.0012-0.0039 in
Top Production Gap	0.254-0.457 mm	0.010-0.018 in
Top Service Limit Gap	0.254-0.711 mm	0.010-0.028 in
Second Production Gap	0.406-0.609 mm	0.016-0.024 in
Second Service Limit Gap	0.406-0.863 mm	0.016-0.034 in
Piston Ring Oil
Production Groove Clearance	0.127-0.165 mm	0.0050-0.0065 in
Service Limit Groove Clearance	0.127-0.191 mm	0.0050-0.0075 in
Production Gap	0.254-0.762 mm	0.010-0.030 in
Service Limit Gap	0.254-1.016 mm	0.010-0.040 in
Piston Pin
Diameter	25.132-25.137 mm	0.9895-0.9897 in
Clearance in Piston Production	0.005-0.017 mm	0.0002-0.0007 in
Clearance in Piston Service Limit	0.005-0.025 mm	0.0002-0.0010 in
Fit in Rod	0.078-0.053 mm Interference	0.0031-0.0021 in Interference
Crankshaft
Crankshaft Run Out	0.051 mm (Maximum)	0.002 in (Maximum)
Main Journal Diameter #1, #2, #3, #4, #5	69.804-69.822 mm	2.7482-2.7489 in
Main Journal Taper Production	0.010 mm (Maximum)	0.0004 in (Maximum)
Main Journal Taper Service Limit	0.025 mm (Maximum)	0.0010 in (Maximum)
Main Journal Out Of Round Production	0.010 mm (Maximum)	0.0004 in (Maximum)
Main Journal Out Of Round Service Limit	0.025 mm (Maximum)	0.0010 in (Maximum)
Main Bearing Clearance #1 Production	0.043-0.076 mm	0.0017-0.0030 in
Main Bearing Clearance #2, #3, #4 Production	0.028-0.061 mm	0.0011-0.0024 in
Main Bearing Clearance #5 Production	0.063-0.096 mm	0.0025-0.0038 in
Main Bearing Clearance #1, #2, #3, #4 Service Limit	0.025-0.076 mm	0.0010-0.0030 in
Main Bearing Clearance #5 Service Limit	0.063-0.101 mm	0.0025-0.0040 in
Crankshaft End Play	0.127-0.279 mm	0.005-0.011 in
Crankpin Diameter	55.854-55.869 mm	2.1990-2.1996 in
Crankpin Taper Production	0.0127 mm	0.0005
Crankpin Taper Service Limit	0.025 mm	0.0010 in
Crankpin Out Of Round Production	0.013 mm	0.0005
Crankpin Out Of Round Service Limit	0.025 mm	0.0010 in
Rod Bearing Clearance Production	0.028-0.074 mm	0.0011-0.0029 in
Rod Bearing Clearance Service Limit	0.028-0.099 mm	0.0011-0.0039 in
Rod Side Clearance	0.033-0.584 mm	0.0013-0.0230 in
Camshaft
Camshaft Run Out	0.051 mm (Maximum)	0.002 in (Maximum)
Lobe Lift Intake ± 0.05 mm (0.002 in)	7.165 mm	0.2821 in
Lobe Lift Exhaust ± 0.05 mm (0.002 in)	7.221 mm	0.2843 in
Journal Diameter	49.471-49.522 mm	1.9477-1.9497 in
Valve System
Lifter	Hydraulic, Roller Followers
Rocker Arm Ratio	1.70:1
Valve Lash Intake	Net Lash
Valve Lash Exhaust	Net Lash
Face Angle (Intake & Exhaust)	45 degrees
Seat Angle (Intake & Exhaust)	46 degrees
Seat Runout (Intake & Exhaust)	0.051 mm (Maximum)	0.002 in (Maximum)
Seat Width Intake	0.762-1.524 mm	0.030-0.060 in
Seat Width Exhaust	1.524-2.413 mm	0.060-0.095 in
Stem Clearance Production Intake	0.025-0.0737 mm	0.0010-0.0029 in
Stem Clearance Production Exhaust	0.030-0.077 mm	0.0012-0.0031 in
Stem Clearance Service Intake	0.025-0.094 mm	0.0010-0.0037 in
Stem Clearance Service Exhaust	0.030-0.124 mm	0.0012-0.0049 in
Valve Spring Pressure Closed	316-351 N @ 46.685 mm	71-79 lb @ 1.838 in
Valve Spring Pressure Open	1059-1165 N @ 34.213 mm	238-262 lb @ 1.347 in
Valve Spring Installed Height ± 0.794 mm (0.0312 in)	46.685 mm	1.838 in