Circuit Description
The Accelerator Pedal Position (APP) module provides a voltage signal that changes relative to the accelerator pedal position. There are three sensors located within the APP module that are scaled differently. This is a type D DTC.
Conditions for Setting the DTC
| • | The voltage is less than 0.25 volts on the APP 3 sensor. |
| • | The conditions were met for 2 seconds. |
Action Taken When the DTC Sets
| • | The input from the APP 3 sensor is ignored. |
| • | This DTC will not turn the Service Throttle Soon lamp ON by itself. |
| • | The throttle will operate normally as long as there is only one malfunction present. If two different APP sensors have a malfunction, the Service Throttle Soon lamp will light and the PCM will limit the power. If the three APP sensors have a malfunction present, the Service Throttle Soon lamp will light and the PCM will only allow the engine to operate during idle. |
Conditions for Clearing the MIL/DTC
| • | A History DTC will clear after forty consecutive warm-up cycles during which the diagnostic does not fail (the coolant temperature has risen 5°C (40°F) from the start up coolant temperature and the engine coolant temperature exceeds 71°C (160°F) during that same ignition cycle). |
| • | Use of a Scan tool will clear the DTC codes. |
Diagnostic Aids
There are no driveability issues associated with the APP module unless a DTC is present. The most likely cause of this DTC are poor connections or the sensor itself. The least likely is a PCM problem.
A scan tool reads the APP 3 position in volts. The scan tool should read about 4.0 volts with the throttle closed and the ignition ON or during idle. The voltage should decrease at a steady rate as the throttle is moved toward a Wide Open Throttle (WOT). Also, 90% pedal travel is acceptable for a correct APP operation. Scan the APP 3 sensor while depressing the accelerator pedal with the engine stopped and the ignition ON. The display should vary from about 4.0 volts when the throttle is closed to about 2.0 volts when the throttle is held at a Wide Open Throttle (WOT) position.
Test Description
The number(s) below refer to the Step number(s) on the Diagnostic Table.
-
This Step will determine if DTC P0227 is the result of a hard failure or an intermittent condition.
-
This Step checks the PCM and the wiring.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Important: Before clearing the DTCs, use the Scan Tool Capture Info in order to record the Freeze Frame and the failure records for reference, as the data will be lost when the Clear Info function is used. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
Is the APP 3 voltage less than or equal to the specified value? | 0.25V | |||
The DTC is intermittent. If no additional DTCs are stored, refer to Diagnostic Aids. If any additional DTCs were stored, refer to those table(s) first. Are there any additional DTCs stored? | -- | Go to the Applicable DTC Table | Go to Diagnostic Aids | |
4 |
Is the voltage at the specified value? | 5V | ||
5 | Use J 39200 in order to probe the APP 3 signal circuit at the APP harness. Is the voltage at the specified value? | 5V | ||
6 |
Was the 5 volt reference circuit open or shorted to ground? | -- | ||
7 | Check the 5 volt reference circuit for a poor connection at the PCM and replace the terminal if necessary. Did the terminal require a replacement? | -- | ||
8 |
Was the APP 3 signal circuit open or shorted to ground? | -- | ||
9 | Check the APP 3 sensor signal circuit for a poor connection at the PCM and replace the terminal if necessary. Did the terminal require a replacement? | -- | ||
10 | Check for a poor electrical connection at the APP sensor. Was a repair performed? | -- | ||
11 | Replace the APP module. Refer to APP Module Replacement . Is the action complete? | -- | -- | |
12 | Replace the PCM. Important: If the PCM is malfunctioning, the new PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Is the action complete? | -- | -- | |
13 |
Does the Scan Tool indicate that this diagnostic Ran and Passed? | -- | ||
14 | Use the Scan Tool in order to select Capture Info, Review Info. Are there any DTCs displayed that have not been diagnosed? | -- | Go to the Applicable DTC Table | System OK |
