DTC P1133 HO2S Insufficient Switching Bank 1 Sensor 1. Chevrolet Chevy G Van 1996

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1996 🢒 Chevy G Van 🢒 DTC 🢒 DTC P1133 HO2S Insufficient Switching Bank 1 Sensor 1

Engine Controls Components
CKP, CMP Sensors, ICM with Ignition Coil
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

Important: If the voltage is measured with a 10 Megaohm Digital Voltmeter, the voltage may read as low as 0.32 volt (320 mV).

The VCM supplies a voltage of about 0.45 volt between the HO2S High and the HO2S Low circuits. The Heated Oxygen Sensor (HO2S) varies the voltage from approximately 1.0 volt (1000 mV) during rich conditions to 0.10 volt (100 mV) during lean conditions.

The sensor acts like an open circuit and produces no voltage at temperatures below 360°C (600°F). An open oxygen sensor circuit or a cold oxygen sensor causes an Open Loop operation.

The HO2S heater provides for a faster sensor warm-up. This allows the sensor to become active in a shorter period of time and remain active during a long extended idle.

The DTC P1133 determines if the HO2S is functioning properly by the monitoring the number of the Lean to Rich and the Rich to Lean transition. The DTC P1133 is a type B DTC.

Conditions for Setting the DTC

The following conditions sets the DTC:

•	No fuel trim DTCs

•	L/R switches less than 30.

•	R/L switches less than 30.

•	No TP sensor DTCs

•	No EVAP DTCs

•	No IAT sensor DTCs

•	No MAP DTCs

•	No EGR DTCs

•	No ECT sensor DTCs

•	The DTC P0135 not set

•	Closed Loop

•	HO2S voltage between 0.300 volts and 0.600 volts

•	Throttle position is greater than 10% but less than 20%.

Action Taken When DTC Sets

The VCM turns the MIL ON after the second test failure.

Conditions for Clearing the MIL/DTC

The VCM turns OFF the MIL after 3 consecutive driving trips without a fault condition present. A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles (the coolant temperature has risen 22°C (40°F) from the start-up coolant temperature and the engine coolant temperature exceeds 71°C (160°F) during that same ignition cycle) or the scan tool clearing feature has been used.

Diagnostic Aids

Check the HO2S heater operation.

Never solder the HO2S wires. For proper wire and connector repairs, refer to Wiring Repairs .

Test Description

The numbers below refer to the step numbers in the diagnostic table.

This step checks for other DTCs.

This step checks for any physical damage to the engine components and the converter.

This step checks the fuel injector and isolates the HO2S.

Step

Action

Value(s)

Yes

Important: Before clearing DTCs, use the scan tool in order to record the freeze frame and the failure records for reference because the Clear Info function will lose the data.

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Are any other DTCs set?

Go to The Applicable DTC Table

Go to Step 4

Allow the engine to idle.
Monitor the MAP sensor voltage on the scan tool.

Is the MAP sensor voltage greater then the specified value?

4.0 V

Go to DTC P0108 Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage

Go to Step 5

Visually and Physically check for the following conditions:

•	The air intake duct for improper installation

•	The air intake duct for collapsed or restriction, for missing or plugged air filter

•	The throttle body and intake manifold for vacuum leaks

•	The throttle body for damage to the inlet or for foreign objects partially blocking the inlet

•	The throttle body for coking or objects blocking IAC valve passages

•	Exhaust system for corrosion, leaks, loose or missing hardware

•	The HO2S sensor is installed securely and pigtail harness is not contacting exhaust manifold or wires.

•	The vacuum hoses for splits, kinks and proper connections

•	The fuel for excessive water, alcohol or other contaminants

•	The VCM sensor grounds are clean, tight and in their proper location

•	Fuel Pressure Regulator. Refer to Table A-6.

Was a problem found?

Go to Step 5

Go to Step 6

Repair as necessary. Replace as necessary.

Is the action complete?

Go to Step 11

Perform Injector Coil test procedure. Refer to Table A-8.

Was a problem found?

Go to Step 9

Go to Step 7

Remove the HO2S (Bank 1, Sensor 1).
Inspect for contamination.

Is a contamination evident?

Go to Step 8

Go to Diagnostic Aids

Replace the contaminated HO2S (Bank 1, Sensor 1). Refer to Heated Oxygen Sensor (HO2S) Replacement .

Is the action complete?

Go to Step 10

Replace the fuel injector. Refer to Fuel Injector Replacement.

Is the action complete?

Go to Step 10

Using the scan tool, select the DTC and the Clear Info.
Start the Engine.
Idle at the normal operating temperature.
Select the DTC and the Specific.
Enter the DTC number which was set.
Operate the vehicle within the conditions for setting this DTC as specified in the supporting text.

Does the scan tool indicate that this diagnostic ran and passed?

Go to step 11

Go to Step 2

Using the scan tool, select the Capture Info and the Review Info.

Are any additional DTCs displayed that have not been diagnosed?

Go to The Applicable DTC Table

System OK.