Circuit Description
The Mass Air Flow (MAF) sensor measures the amount of air entering the engine during a given time. The VCM uses the mass air flow information for the fuel delivery calculations. A large quantity of air entering the engine indicates an acceleration or high load situation. A small quantity of air indicates a deceleration or an idle situation.
The MAF sensor produces a frequency signal which can be monitored by using a scan tool. The frequency varies within a range of around 5 to 7 g/s at idle to approximately 125 g/s at the maximum engine load. This DTC is a type A DTC.
Conditions for Setting the DTC
The following conditions will set the DTC:
| • | The engine is running |
| • | No TP sensor DTCs |
| • | No MAP sensor DTCs |
| • | No EVAP DTCs |
| • | EGR DTC P0401 not active |
| • | MAF DTCs P0101 or P0103 not active |
| • | The system Voltage is greater than 10.0 volts but less than 17.0 volts |
| • | The Canister Purge Duty Cycle is less than 99% |
| • | The change in throttle position is less than 3.9% |
| • | The EGR duty cycle is no more than 89.9% |
| • | The EGR Pintle Position is no more than 89.9% |
| • | The MAP is no more than 90 kPa |
| • | The throttle position is no more than 89.8% |
| • | The above conditions met for greater than 2 seconds |
| • | The change in MAF sensor is greater than a calculated value |
Action Taken When the DTC Sets
| • | The VCM illuminates the Malfunction Indicator Lamp (MIL) the first time the fault is detected. |
| • | The VCM calculates an airflow value based on the idle air control (IAC) valve position, the throttle position, the engine speed, and the barometric pressure. |
| • | The VCM will store the conditions which were present when the DTC set as Freeze Frame and the Fail Records data. |
Conditions for Clearing the MIL or DTC
| • | The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed. |
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle. |
| • | Use a scan tool in order to clear the DTCs. |
Diagnostic Aids
Check for the following conditions:
| • | A skewed or stuck TP sensor. A malfunctioning TP sensor or TP sensor circuit can cause the VCM to incorrectly calculate the predicted mass air flow value. Observe the Throttle Angle with the throttle closed. If the Throttle Angle reading is not 0%, check for the following conditions: |
| - | The throttle plate sticking or excessive deposits on the throttle plate or the throttle bore |
| - | The TP sensor signal circuit is shorted to voltage |
| - | A Poor connection or high resistance in the TP sensor ground circuit. |
| - | If none of the above conditions are noted and the Throttle Angle reading at closed throttle is not 0%, replace the TP sensor. |
| • | Inspect harness connectors for the following conditions: |
| - | Backed out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Improperly formed or damaged terminals |
| - | Poor terminal to wire connection |
| • | A misrouted harness. Inspect the MAF sensor harness in order to ensure that it is not routed too close to high voltage wires such as spark plug leads. |
| • | A damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, observe the scan tool while moving the connectors and the wiring harnesses related to the MAF sensor. A change in the display indicates the location of the fault. |
| • | A plugged intake air duct or a dirty air filter element. A wide open throttle acceleration from a stop should cause the Mass Air Flow displayed on a scan tool to increase from about 4-7 gm/s at idle to 100 gm/s or greater at the time of the 1-2 shift. If not, check for a restriction. |
| • | A skewed MAP sensor. A skewed MAP sensor can cause the BARO reading to be incorrectly calculated. In order to check the MAP sensor, compare the BARO reading on the vehicle being diagnosed to the BARO reading on a normally operating vehicle. If a large difference is noted (over 8 kPa), replace the MAP sensor. Refer to MAP Sensor Replacement . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies that the problem is present at idle.
-
A voltage reading of less than 4.0 volts or over 6.0 volts at the MAF sensor signal circuit indicates a fault in the wiring or a poor connection.
-
This step verifies that the ignition feed circuit voltage and a good ground are available at the MAF sensor.
Step | Action | Value(s) | Yes | No | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 |
Important: Before clearing DTCs, use the scan tool in order to record the freeze frame and the failure records for reference because the Clear Info function will lose the data. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||||||||
Does the scan tool indicate DTC P0101 Failed This Ign? | -- | Refer to The Diagnostic Aids | ||||||||||||
3 |
Was a problem found? | -- | ||||||||||||
4 |
Does the scan tool display YES? | -- | ||||||||||||
Is the voltage near the specified value? | 5.0 V | |||||||||||||
Connect a test lamp between the MAF sensor ignition feed and ground circuits at the MAF sensor harness connector. Is the test lamp on? | -- | |||||||||||||
7 | Is the voltage less than the specified value? | 4.5 V | ||||||||||||
8 |
Is the voltage near the specified value? | 0.0 V | ||||||||||||
9 | Connect a test lamp between the MAF sensor ignition feed circuit and the chassis ground. Is the test lamp on? | -- | ||||||||||||
10 |
Did you find a poor connection? | -- | ||||||||||||
11 |
Was the MAF signal circuit open or shorted? | -- | ||||||||||||
12 | Repair the open in the ground circuit to the MAF sensor. Refer to Wiring Repairs in Engine Electrical. Is the action complete? | -- | -- | |||||||||||
13 | Repair the open in the ignition feed circuit to the MAF sensor. Refer to Wiring Repairs in Engine Electrical. Is the action complete? | -- | -- | |||||||||||
14 | Repair the short to voltage in the MAF sensor signal circuit. Refer to Wiring Repairs in Engine Electrical. Is the action complete? | -- | -- | |||||||||||
15 | Replace the MAF sensor. Refer to MAF Sensor Replacement . Is the action complete? | -- | -- | |||||||||||
16 | Replace the VCM. Important: If the VCM is faulty, reprogram the VCM. Refer to VCM Replacement/Programming . Is the action complete? | -- | -- | |||||||||||
17 |
Does the scan tool indicate that this diagnostic ran and passed? | -- | ||||||||||||
18 | Using the scan tool, select the Capture Info and the Review Info. Are any DTCs displayed that have not been diagnosed? | -- | Go to The Applicable DTC Table | System OK |
