GM Service Manual Online
For 1990-2009 cars only

Generator Bracket Replacement 6.6L Engine

Removal Procedure


    Object Number: 665386  Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 6.6L.
  3. Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical-6.6L.
  4. Remove the upper fan shroud. Refer to Engine Coolant Fan Upper Shroud Replacement in Engine Cooling.
  5. Remove the outlet heater hose bracket bolt (2).

  6. Object Number: 660347  Size: SH
  7. Remove the generator bolts and reposition the generator aside. The electrical connections can remain attached to the generator.

  8. Object Number: 798945  Size: SH
  9. Remove the right idler pulley bolt and pulley.
  10. Remove the left idler pulley bolt and pulley.
  11. Remove the drive belt tensioner bolt and tensioner.

  12. Object Number: 698198  Size: SH
  13. Remove the fuel bleed valve nuts and valve.
  14. Reposition the oil separator hose clamp at the side of the generator bracket.
  15. Remove the oil separator hose from the pipe.

  16. Object Number: 788902  Size: SH
  17. If equipped, remove the vacuum line from the exhaust gas recirculation (EGR) valve vacuum pump.

  18. Object Number: 788903  Size: SH
  19. If equipped, remove the EGR vacuum pump bolts. Reposition the vacuum pump.
  20. Reposition the oil separator hose clamp at the bottom of the generator bracket.
  21. Remove the oil separator hose from the bracket.

  22. Object Number: 798876  Size: SH
  23. Remove the generator bracket bolts.
  24. Remove the generator bracket.

Installation Procedure


    Object Number: 798876  Size: SH
  1. Install the generator bracket.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the generator bracket bolts.
  4. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).


    Object Number: 788903  Size: SH
  5. Install the oil separator hose to the bracket.
  6. Position the oil separator hose clamp at the bottom of the generator bracket.
  7. If equipped, position the vacuum pump. Install the EGR vacuum pump bolts.
  8. Tighten
    Tighten the bolts to 22 N·m (16 lb ft).


    Object Number: 788902  Size: SH
  9. If equipped, install the vacuum line to the EGR valve vacuum pump.

  10. Object Number: 698198  Size: SH
  11. Install the oil separator hose to the pipe.
  12. Position the oil separator hose clamp at the side of the generator bracket.
  13. Install the fuel bleed valve and nuts.
  14. Tighten
    Tighten the nuts to 25 N·m (18 lb ft).


    Object Number: 798945  Size: SH
  15. Install the drive belt tensioner and bolt. Align the pin on the tensioner with the hole in the bracket.
  16. Tighten
    Tighten the bolt to 41 N·m (30 lb ft).

  17. Install the left idler pulley and bolt.
  18. Install the right idler pulley and bolt.
  19. Tighten
    Tighten the bolts to 43 N·m (32 lb ft).


    Object Number: 660347  Size: SH
  20. Position the generator and install the bolts.
  21. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).


    Object Number: 665386  Size: SH
  22. Install the outlet heater hose bracket bolt (2).
  23. Tighten
    Tighten the bolt to 25 N·m (18 lb ft).

  24. Install the upper fan shroud. Refer to Engine Coolant Fan Upper Shroud Replacement in Engine Cooling.
  25. Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical-6.6L.
  26. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 6.6L.
  27. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Generator Bracket Replacement 4.3L Engine

Removal Procedure


    Object Number: 360851  Size: SH
  1. Loosen the air cleaner outlet duct clamp at the mass air flow/intake air temperature (MAF/IAT) sensor.

  2. Object Number: 701705  Size: SH
  3. Remove the positive crankcase ventilation (PCV) hose.

  4. Object Number: 489179  Size: SH
  5. Remove the air cleaner adapter nut.

  6. Object Number: 489176  Size: SH
  7. In order to remove the air cleaner outlet duct, pivot the duct upward until the hinge clip releases from the lip on the throttle body.
  8. Remove the cooling fan. Refer to Fan Replacement in Engine Cooling.
  9. Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 4.3L.

  10. Object Number: 334162  Size: SH
  11. Remove the wiring harness bracket bolt.

  12. Object Number: 316440  Size: SH
  13. Remove the heater hose bracket bolt.
  14. Remove the generator. Refer to Generator Replacement .
  15. Remove the drive belt tensioner. Refer to Drive Belt Tensioner Replacement in Engine Mechanical - 4.3L.
  16. Remove the drive belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Right Side or Drive Belt Idler Pulley Replacement - without Air Conditioning in Engine Mechanical - 4.3L.

  17. Object Number: 196643  Size: SH
  18. Remove the generator bracket bolts and nut.
  19. Remove the generator bracket.

Installation Procedure


    Object Number: 196643  Size: SH
  1. Install the generator bracket.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the generator bracket bolts and nut.
  4. Tighten
    Tighten the bolts/nut to 41 N·m (30 lb ft).

  5. Install the drive belt idler pulley. Refer to Drive Belt Idler Pulley Replacement - Right Side or Drive Belt Idler Pulley Replacement - without Air Conditioning in Engine Mechanical - 4.3L.
  6. Install the drive belt tensioner. Refer to Drive Belt Tensioner Replacement in Engine Mechanical - 4.3L.
  7. Install the generator. Refer to Generator Replacement .

  8. Object Number: 316440  Size: SH
  9. Install the heater hose bracket bolt.
  10. Tighten
    Tighten the bolt to 25 N·m (18 lb ft).


    Object Number: 334162  Size: SH
  11. Install the wiring harness bracket bolt.
  12. Tighten
    Tighten the bolt to 25 N·m (18 lb ft).

  13. Install the cooling fan. Refer to Fan Replacement in Engine Cooling.
  14. Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 4.3L.

  15. Object Number: 489176  Size: SH
  16. Align the hinge clip with the lip on the throttle body.
  17. In order to install the air cleaner outlet duct, pivot the air cleaner outlet duct downward until the mounting stud is through the hole.


    Object Number: 489179  Size: SH
  18. Install the air cleaner adapter nut.

  19. Object Number: 701705  Size: SH
  20. Install the PCV hose.

  21. Object Number: 360851  Size: SH
  22. Tighten the air cleaner outlet duct clamp at the MAF/IAT sensor.
  23. Tighten
    Tighten the clamp to 4 N·m (35 lb in).

Generator Bracket Replacement 4.8L, 5.3L, and 6.0L Engines

Removal Procedure


    Object Number: 759636  Size: SH
  1. Remove the battery cable junction block bracket bolts.

  2. Object Number: 847280  Size: SH
  3. Remove the generator. Refer to Generator Replacement .
  4. Remove the power steering pump. Refer to Power Steering Pump Replacement .
  5. Remove the generator bracket bolts.
  6. Remove the generator bracket.

Installation Procedure


    Object Number: 847280  Size: SH
  1. Install the generator bracket.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the generator bracket bolts.
  4. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).

  5. Install the power steering pump. Refer to Power Steering Pump Replacement .
  6. Install the generator. Refer to Generator Replacement .

  7. Object Number: 759636  Size: SH
  8. Install the battery cable junction block bracket bolts.
  9. Tighten
    Tighten the bolts to 9 N·m (80 lb in).

Generator Bracket Replacement 8.1L Engine

Removal Procedure


    Object Number: 759640  Size: SH
  1. Remove the battery cable junction block bracket bolts.

  2. Object Number: 751458  Size: SH
  3. Remove the fan and clutch. Refer to Fan Clutch Replacement .
  4. Remove the drive belt idler pulley. Refer to Drive Belt Idler Pulley Replacement
  5. .

  6. Remove the generator. Refer to Generator Replacement .
  7. Remove the generator bracket bolts and nut.
  8. Remove the generator bracket stud.
  9. Remove the generator bracket.

Installation Procedure


    Object Number: 751458  Size: SH
  1. Install the generator bracket.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the generator bracket stud.
  4. Tighten
    Tighten the stud to 20 N·m (15 lb ft).

  5. Install the generator bracket bolts and nut.
  6. Tighten
    Tighten the bolts and nut to 50 N·m (37 lb ft).

  7. Install the generator. Refer to Generator Replacement .
  8. Install the drive belt idler pulley. Refer to Drive Belt Idler Pulley Replacement .
  9. Install the fan and clutch. Refer to Fan Clutch Replacement .

  10. Object Number: 759640  Size: SH
  11. Install the battery cable junction block bracket bolts.
  12. Tighten
    Tighten the bolts to 9 N·m (80 lb in).