GM Service Manual Online
For 1990-2009 cars only

Object Number: 33179  Size: SF
Engine Controls Components
Engine Controls Schematics
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The Engine Coolant Temperature (ECT) sensor is a thermistor which controls the signal voltage to the VCM. The VCM applies a voltage on a 5 volt reference circuit to the sensor. When the engine coolant is cold, the sensor's internal resistance is high resulting in a high voltage ECT Sensor Signal. As the engine coolant temperature increases, the sensor's internal resistance and ECT Sensor Signal decrease. This DTC is a type A DTC.

Conditions for Setting the DTC

The following conditions will set the DTC:

    • The engine is running
    • Signal voltage is less than 0.78 volts for 5 seconds

Action Taken When the DTC Sets

The VCM turns the MIL ON when P0117 is reported and 1 failure has occurred.

Conditions for Clearing the MIL/DTC

The VCM turns OFF the MIL after 3 consecutive driving trips without a fault condition present. A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles (the coolant temperature has risen 22°C (40°F) from the start-up coolant temperature and the engine coolant temperature exceeds 71°C (160°F) during that same ignition cycle) or the scan tool clearing feature has been used.

Diagnostic Aids

After starting the engine, the temperature should rise steadily to about 90°C (194°F) then stabilize when the thermostat opens.

Check for an intermittent short to ground in the ECT sensor signal circuit by moving the VCM harness at various locations and monitoring the ECT voltage on the scan tool. If the voltage varies, look for a short to ground in the area of the harness that caused the variance.

Use the Temperature vs. Resistance Value Table to test the coolant sensor at various temperature levels in order to evaluate the possibility of a skewed (mis-scaled) sensor. A skewed sensor could result in poor driveability concerns. Refer to Temperature vs Resistance .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. If the fault is still present, the engine coolant voltage will measure less than 0.82 volts.

  2. This test simulates a DTC P0118. If the VCM recognizes the high signal voltage and the scan tool display reads 40 volts or more, the VCM and the wiring are okay.

Step

Action

Value(s)

Yes

No

1

Important: Before clearing DTCs, use the scan tool in order to record freeze frame and the failure records for reference because the Clear Info function will lose the data.

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

  1. Connect the scan tool.
  2. Start the engine.
  3. Monitor the Engine Coolant Temperature (ECT) sensor voltage.

Does the scan tool display an ECT sensor voltage less than the specified value?

0.82 V

Go to Step 3

Go to Step 5

3

  1. Turn off the engine.
  2. Turn ON the ignition.
  3. Disconnect the ECT sensor connector.

Does the scan tool display an ECT sensor voltage greater than the specified value?

4.0 V

Go to Step 7

Go to Step 4

4

  1. Turn off the ignition.
  2. Using the J 39200 , check the resistance across the ECT sensor harness connector.

Is the resistance at the specified value?

Go to Step 8

Go to Step 6

5

The DTC is intermittent. If no additional DTCs are stored, refer to the Diagnostic Aids. If the additional DTCs are stored, refer to those tables first.

--

Go to The Applicable DTC Table

Go to Step 6

6

Repair the short to the ground in the ECT signal circuit. Refer to Wiring Repairs in Engine Electrical.

Is the action complete?

--

Go to Step 9

--

7

Replace the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement .

Is the replacement complete?

--

Go to Step 9

--

8

Replace the VCM.

Important:  If the VCM is faulty, reprogram the VCM. Refer to VCM Replacement/Programming .

Is the replacement complete?

--

Go to Step 9

--

9

  1. Using the scan tool, select the DTC and the Clear Info.
  2. Start the Engine.
  3. Idle the Engine at the normal operating temperature.
  4. Select the DTC and the Specific.
  5. Enter the DTC number which was set.
  6. Operate the vehicle within the conditions for setting this DTC as specified in the supporting text.

Does the scan tool indicate that this diagnostic ran and passed?

--

Go to Step 10

Go to Step 2

10

Using the scan tool, select the Capture Info and the Review Info.

Are any DTCs displayed that have not been diagnosed?

--

Go to The Applicable DTC Table

System OK