Diagnosis will be much easier once you have identified a vibration as first-order of driveline rotation during the road test. Then identify the exact area that the vibration is coming from and take proper action.

In most cases, vibration may be reproduced in the stall. In the stall the vibration may be better or worse than that experienced during the road test.

The objective is to reduce the vibration to the lowest point possible in the stall, than evaluate the results on a road test. Many times, a vibration you were able to reduce drastically in the stall will be completely eliminated on the road.

The cause of first-order drive line vibration is usually excessive runout or an imbalanced component.

The following procedure offers a systematic process of elimination in order to determine which component is at fault:

1. Raise the vehicle to curb height. Support the vehicle on a hoist or heavy stands. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the rear tire/wheel assemblies. Refer to Wheel Removal in Tires and Wheels.
3. Inspect the propeller shaft. The propeller shaft should be free of undercoating before continuing this diagnosis.
4. Inspect the propeller shaft or U-joints for any obvious dents or damage. Dents or damage will contribute to first-order driveline vibrations.
5. Start the engine.
6. Place the transmission in gear.
7. Run the vehicle up to the speed at which the vibration was most severe.
8. Note the vibration present, and at what speed.
9. If the vibration is not present, refer to First-Order Driving Vibration Testing (Torque Sensitive) in the Road Testing Diagnosis.
10. If the vibration is present, determine which end of the driveshaft is vibrating the most. Hold your hand against the pinion nose and the transmission tailshaft, or hold an EVA vibration sensor up to each component.
11. Inspect the center support bearing for vibration.
12. If the transmission tailshaft is vibrating, touch the transmission crossmember under the transmission mount. If there is no vibration on the crossmember, then the transmission mount is working properly.
13. Note which end of the driveshaft is the worst, and how severe the vibration is. The inspection will be a reference by which to judge future progress.

Do not fill the propeller shaft with foam, oil, or any other substance in order to correct a vibration. Filling the propeller shaft is only effective in reducing an unrelated condition called Torsional Rattle. Filling the propeller shaft should only be done in strict adherence to the procedure outlined in corporate bulletins that address Torsional Rattle. Failure to follow the correct procedure will induce a vibration and/or affect the structural integrity of the propeller shaft. The propeller shaft will then have to be replaced.

A propeller shaft or pinion (companion) flange with excessive runout causes first-order driveline vibrations. Use the following procedure in order to measure runout of the propeller shaft. The tolerances are critical for smooth operation of the driveline.

Tools Required

1. Raise the vehicle on a suitable hoist. Refer to Lifting and Jacking the Vehicle in General Information.
2. Allow the wheels to spin freely.
3. AttachJ 8001 andJ 7872 .
4. Place the transmission in Neutral. Rotate the pinion flange or transmission yoke by hand while taking the measurements for runout. The propeller shaft will turn easier in one direction than in the other.
5. For three-piece propeller shafts, if the runout exceeds the tolerances at one or more points:

5.1.	Measure the rear propeller shaft.

5.2.	Mark the position of the rear shaft in the pinion flange, then remove the rear shaft.

5.3.	Measure intermediate propeller shaft.

5.4.	Measure the front propeller shaft runout on the tube and the stub shaft.

5.5.	Replace the propeller shaft if either measurement is out of tolerance.

Refer to Propeller Shaft Runout Specifications .

Important: When you replace a propeller shaft, check the new shaft for runout. Double-check the pinion flange runout if the replacement shaft runout is also out of tolerance.

Tools Required

1. Place the vehicle on a suitable hoist. Refer to Lifting and Jacking the Vehicle in General Information. Allow the wheels to rotate freely.
2. Remove the propeller shaft from the pinion flange.



3. Install the J 35819 .

Important: The dial indicator will have inverted readings. You are measuring the inside diameter of the flange, and not the outside diameter. The highest reading on the dial indicator is the low spot. The lowest reading is the high spot.

4. Rotate the pinion shaft 360 degrees and zero the dial indicator on the low spot.
5. Rotate the pinion flange again and record the total runout.
6. If the pinion flange runout is 0.15 mm (0.006 in) or less, remove the pinion flange balance weight.
7. If the pinion flange runout is over 0.15 mm (0.006 in) but no less than 0.28 mm (0.011 in), and the runout compensation weight is at or near the low spot, then no further action is necessary. Remove the weight if the runout compensation weight is not at or near the low spot.
8. If the pinion flange runout is more than 0.28 mm (0.011 in) but no greater than 0.38 mm (0.015 in), and the balance weight is at or near the low point, then no further action is necessary. Remove the weight and re-index the pinion flange until the runout is 0.25 mm (0.010 in) or less if the runout compensation weight is not at or near the low spot.
9. Replace the pinion shaft when the runout is 0.25 mm (0.010 in) or less. Then, recheck the runout. Service replacement flanges do not have balance weights.

Helpful Hints

•	If necessary, add compensation weights on the face of the pinion flange dust slinger. These weights are tack-welded onto the slinger. You may remove the weights with a die-grinder.

Most first-order driveline vibrations originate at the pinion nose end of the driveshaft. Ensure that the vibrations are at a minimum at this location in order to achieve acceptable results. Reduce the runout of the components to a minimum. Balance the driveline as a system when necessary.

1. Measure the runout of the propeller shaft and check the tolerance.
2. If the tolerance is excessive, mark the position of the shaft for future reference and rotate the shaft 180 degrees.
3. Reinstall the shaft and recheck the runout. Inspect the level of vibration in order to determine if the vibration is lower or corrected.
4. If the runout is still excessive, or if the vibration is still present, refer to Measuring Pinion Flange Runout. Replace the pinion flange or re-index the flange 180 degrees if the pinion flange runout exceeds the tolerance.

Remove and reinstall the pinion flange only once on axles utilizing a "crush" type sleeve. Replace the sleeve with a new sleeve if the sleeve is "crushed". Removing the sleeve requires removal of the ring and pinion set. Therefore, replace flanges with excessive runout. Regardless of the method used, measure the pinion flange runout in order to ensure that the flange is within tolerance.

5. Recheck the propeller shaft runout if the vibration is present after the pinion flange runout is corrected. If the propeller shaft runout is still excessive, correct the runout before doing a driveline system balance. Either replace the shaft with a shaft that is within tolerance or sublet the shaft to a reputable independent for straightening and re-balance. Ensure that the new or rebuilt shaft is within runout tolerance before you continue.
6. Once the propeller shaft and pinion flange are within runout tolerances, check if the vibration is gone. If the level of the vibration is still unacceptable, perform a driveline system balance procedure.

First-order driveline vibrations that originate at the transmission end of the propeller shaft are rare. If the tailshaft of the transmission is vibrating, inspect the tailshaft housing bushing for wear or damage. A leaky transmission tailshaft oil seal indicates bushing problems.

Feel for vibration at the crossmember underneath the transmission mount. If there is no vibration, the transmission mount is doing its job of isolating the vibration from the structure of the vehicle. The transmission mount is therefore probably not cause of vibration.

Use the following procedure if you can feel vibration on the crossmember and the tailshaft bushing, and if transmission output is normal:

1. Measure the propeller shaft runout. If the runout is excessive, replace the shaft with one that has acceptable runout. Alternatively, sublet the shaft to a reputable independent service shop in order to have the shaft rebalanced and the runout corrected.
2. Test drive the vehicle. If the vibration is still unacceptable, balance the shaft on the vehicle. Refer to Vibration Diagnosis .

First-order driveline vibrations that occur mainly at the center support bearing (2) are usually the result of excessive runout at the stub (splined) shaft (3).

Unlike other first-order driveline vibrations, these vibrations can appear at unusually low speeds of 40 km/h (25 mph) and up.

Follow the following procedure to correct this type of vibration:

1. Mark the position of the rear propeller shaft at both ends for proper reassembly. Remove the rear propeller shaft form the vehicle.
2. Measure the runout of the splines about 12.7 mm (0.5 in) from the end (1).
3. Replace the shaft if the runout exceeds the tolerances.

Stub shaft/spline runout 0.076 mm (0.003 in)

Vibration is eliminated with the correction of the propeller shaft runout. If some vibration is still present, perform a vehicle road test. Then, determine if an on-vehicle system balance is necessary.

To pinpoint the source, you must reproduce the vibration in the service stall and then determine which component is vibrating the most using the EVA:

1. Support the vehicle on a suitable hoist or on safety stands. Ensure that the rear of the rear axle is at curb height. Do not allow the axle to hang. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the rear tire/wheel assemblies. Refer to Wheel Removal in Tires and Wheels.
3. Ensure that the propeller shaft is free of undercoating. Check for dents or damage to the propeller shaft or U-joints.

Caution: Do not run the vehicle higher than 89 km/h (55 mph). Stay clear of the universal joints and the balance weight area in order to avoid personal injury. Do not run the vehicle on the hoist for extended periods of time. Running the vehicle on the hoist for extended periods of time may cause the engine or the transmission to overheat.

4. Start the engine. Place the transmission in gear and run at the vehicle speed at which the vibration occurs at.

Determine which end of the propeller shaft is vibrating the most. Hold the EVAs sensor against the pinion nose and the transmission tailshaft assembly. The higher the amplitude reading, the greater the vibration.

Check the center support bearing.

If the transmission tailshaft vibrates, check the transmission crossmember under the transmission mount. The vibration should not be present if the mount is doing its job.

Ensure that the runout of the various driveline components are within specifications. If the runouts are within specifications, strobe balance the driveline. The EVA is able to simplify the balancing process, using the following procedure:

1. Use the EVA in order to determine which end of the propeller shaft has the most vibration.



2. Mark the end of the propeller shaft (1) that has the most vibration at four points, 90 degrees apart. Number the marks 1 through 4 (2).
3. Mount the EVA sensor onto the bottom of the following components:

•	The differential housing

•	The center bearing support

•	The transmission tailshaft assembly

4. Position the sensor as close to the propeller shaft as possible. Ensure that the UP side of the sensor faces up. Ensure that the sensor is horizontal.
5. Start the engine.
6. Turn off all engine accessories.
7. Place the transmission in gear.
8. Run the vehicle at the speed which causes the most vibration in the propeller shaft.
9. Hook the timing light clip to the trigger wire.
10. Plug the vibration sensor into Input A of the EVA. Input B does not have strobe light capability.
11. Verify that the predominant frequency on the EVA display matches the frequency of the original vibration. Use the strobe light only if the rotation speed of the propeller shaft is the predominant frequency.
12. The EVA displays a series of questions in order to select the correct filter. Press YES in order to select the desired filter. Ensure that the frequency is in the middle of the filter range. Use the full range only as a last resort.
13. The display shows the test frequency, the amplitude and the filter range. The driveline is balanced when the amplitude is near two. In some cases a slightly higher amplitude will provide adequate balance.
14. Point the timing light at the propeller shaft. The strobe effect will appear to freeze the propeller shaft. Note which of the numbered marks is at the bottom of the propeller shaft, or the 6  o'clock position. This position is the light spot.
15. Turn the engine off.
16. Install a weight directly on the light spot.
17. Start the engine.
18. Run the vehicle at peak vibration speed.
19. Strobe the propeller shaft again.

The propeller shaft is balanced if the strobe image is erratic and the amplitude is near two.

The propeller shaft is not balanced if one of the following conditions exist:

If the shaft will not balance using two weights, then place a third weight on the light spot. Split the first two weights in order to produce a total weight between two and three weights.

If three weights fail to balance the driveline, then replace the propeller shaft.

When the propeller shaft balances, road test the vehicle in order to verify that the vibration is eliminated.

The following procedure is designed to fine-tune the balance of the propeller shaft while it is mounted in the vehicle. The procedure also is able correct residual imbalance of the remaining driveline components.

Prior to balancing the driveline system, verify that the propeller shaft and the pinion flange runout are within specification.

Do not overheat the engine when performing this procedure.

1. Raise the vehicle to curb height. Support the vehicle on a hoist or on safety stands. Do not allow the axle to hang. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove the rear tire/wheel assemblies. Refer to Wheel Removal in Tires and Wheels.
3. Determine which end of the propeller shaft has the most vibration in order to identify where to begin installing the hose clamps.



4. Mark the end of the propeller shaft (1) which has the most vibration at four points, 90 degrees apart. Number the marks 1 through 4 (2).

The following procedure uses a trial and error method of determining where to place the hose clamps on the shaft. Use the following tips in order to help locate the clamps:

1. Because the imbalance may be related to propeller shaft runout, begin installing the clamps at the low point of the propeller shaft runout.
2. When the plant workers balance the propeller shaft, they use weights in graduated increments: 1/16 oz (1.77 g), 1/8 oz (3.54 g), etc. If the stock weight is too light or too heavy, place the hose clamp either directly in line with or opposite to the stock weight.

The last method involves road testing the vehicle at a speed which the vibration is felt.

1. Carefully hold a piece of chalk up to the very end of the propeller shaft. Barely touch the chalk to the shaft.
2. Shut the engine off in order to stop the propeller shaft from rotating. Do not step on the brake pedal. Do not put the transmission in Park.
3. Inspect the chalk mark.

If you performed the above procedure correctly, the chalk mark will indicate the heavy spot on the shaft. The heavy spot deflected downward and touched the chalk. If the chalk mark circle the entire shaft, touch the chalk more gently to the shaft. Ensure that the chalk touches only the heavy spot. Once the heavy spot is located, place the hose clamp 180 degrees opposite to the chalk mark. Then perform the following steps:

1. Place the hose clamp at the light spot, or at any of the four points marked previously.
2. Test drive the vehicle at the speed at which the vibration occurred. Record any changes in the vibration.
3. Move the clamp to the other positions.
4. Test drive the vehicle each time the clamp is moved. Record any changes in vibration. Note which position gives the best balance.

If the vibration does not change at all, or gets worse, then one clamp is too light or too heavy.

Continue the trial and error procedure using different weights in different locations until you achieve the best balance. If more that three clamps aligned in the same position are required, then replace the propeller shaft.

If you are able to reduce the vibration in the stall, but are unable to eliminate the vibration completely, perform a road test on the vehicle. A slight vibration noticeable in the stall may not be noticeable on the road.

When using clamps in order to balance a propeller shaft with the total weight method, the correct weight required will often be a fraction or a multiple of one hose clamp. Use the following phasing procedure with two hose clamps in order to accurately place any required amount between zero weights (0.0 total weight) to two weights (2.0 total weight).

Ensure that the clamps are located with even spaces on either side of the light spot, or 180 degrees opposite the heavy spot.

The following table contains the weight amounts in terms of the total weight and the included angle (spread) between the clamps. Refer to Propeller Shaft Runout Specifications .

The main objective of this section is to correct the conditions that interfere with the proper cancellation effect of the U-joints. The most common condition, especially where the launch shudder is concerned, is incorrect driveline working angles. However, other factors may aggravate the condition.

Address these factors before you attempt to measure or correct driveline working angles:

If a second-order driveline vibration exists after these conditions are corrected, measure and correct the driveline angles.

If the complaint is present only with cargo in the vehicle, perform the measurements with the vehicle fully loaded. Once a second-order driveline vibration has been corrected with the vehicle loaded, the vibration may reappear with the vehicle unloaded. The reverse of this is also true. You may have to reach a compromise with the customer in this case.

Tools Required

Driveline working angle does not refer to the angle of any one shaft, but to the angle that is formed by the intersection of two shafts, as shown.

To verify the accuracy of the adapter, check the angle of an accessible joint with the inclinometer prior to assign it on an inaccessible joint.

Raise the vehicle on a suitable hoist or on safety stands. Ensure that the rear axle is supported at curb height and that the wheels are free to spin. Refer to Lifting and Jacking the Vehicle in General Information.

Place the transmission in Neutral. Make sure the vehicle has a full tank of fuel or the equivalent amount of weight in the rear to simulate a full tank 3.8 liters of gasoline (one gallon) weighs approximately 2.8 kg (6.2 lb).

Inspect the propeller shaft for correct phasing. This means that the front and rear U-joints are directly in line or parallel with each other so that proper cancellation takes place.

1. Rotate the propeller shaft so that the propeller shaft rear U-joint bearing cap is vertical as shown.



2. Ensure that the front bearing cap is also vertical.
3. Place the inclinometer on the propeller shaft rear U-joint bearing cap in order to ensure that both U-joints are vertical.
4. Set the indicator line above the sight glass on 15 (the horizontal reference) and rotate the propeller shaft until the bubble centers in the sight glass. This brings the rear U-joint to vertical.
5. Remove the inclinometer without disturbing the setting. Leave the setting on 15 and install the inclinometer on the front U-joint. The bubble should remain centered plus or minus 3 degrees if the shaft is properly phased.

Three-piece propeller shaft systems have four working angles.

The setup and measurement techniques are identical to that of a one-piece propeller shaft system. First, check for proper phasing:

1. Turn the rear shaft so the rear U-joint is straight up and down. Ensure that the front U-joint of the rear propeller shaft is also straight up and down.
2. Rotate the shafts 90 degrees so that the front propeller shaft front U-joint is straight up and down. Ensure that the front propeller shaft is also straight up and down (actually part of the slip yoke on the rear shaft).

If the two U-joints of the front propeller shaft are not in this phase, the two halves of the propeller shaft may have been assembled incorrectly.

The procedure for lateral alignment of a three-piece propeller shaft is used for launch shudder or any second-order, driveline vibrations. Adjust the lateral alignment before you measure and adjust the driveline angles.

1. Raise and suitably support the vehicle on a hoist. Refer to Lifting and Jacking the Vehicle in General Information.
2. Look down the front of the propeller shaft.
3. If the propeller shaft is not straight, or if the center bearing support is off to one side, relocate center support bearing to make the propeller shaft assembly as straight as possible. Ensure that you do not create a ground-out condition against the exhaust or another component.

If launch shudder or second-order driveline vibration is still present, measure and correct the driveline angles.

This procedure is essentially the same as for one-piece propeller shafts. You must, however, take into account the fourth angle.

1. Place the inclinometer on the propeller shaft bearing cap.



2. Center the bubble in the sight glass and record the measurement. The bearing cap must be straight up and down to obtain accurate measurement. Enter the measurements on your diagram.



3. Rotate the propeller shaft 90 degrees and place the inclinometer on the transmission output yoke bearing cap. Again, the bearing cap must be straight up and down to obtain an accurate measurement.
4. Center the bubble in the sight glass and record the measurement.
5. Subtract the smaller reading from the larger reading to obtain the front U-joint working angle.

In order to change the working angles, shim the components up or down. Look closely at the existing angles. Use the existing angles and the shims in order to achieve the correct working angles.

Compared to horizontal or true level, the components located at the rear of the vehicle are usually lower than the components located at the front of the vehicle. This condition is called down in the rear. If a component with a down in the rear angle is shimmed up at the rear, then the shim will bring the component closer to the horizontal (zero). Alternately, if a component with a down in the rear angle is shimmed down, then the component will move farther from the horizontal (zero).

Rear axle wind-up may cause launch shudder even when all of the working angles are within specifications. Rear axle wind-up occurs when heavy torque during acceleration causes the pinion nose to point upward. In order to compensate for axle wind-up, tip the pinion nose downward. Install the axle shims incrementally, performing a road test after each shim. Add shims until the road test indicates that the shudder is eliminated.

Wedge shims of different sizes are available through GMSPO and independent suppliers for the purpose of shimming the rear axle angle. GM shims are available in two, three and four degrees.

Caution: Never attempt to shim a rear axle using anything except shims that are designed for this purpose. Failure to do so will result in the shims falling out and a loss of vehicle control and that could cause personal injury.

Install the shims (5) in order to increase or decrease the angle of the rear axle pinion. Install the shims between the leaf spring (3) and the spring seat (6). Depending on the design of the suspension (leaf spring on top or underneath the axle), and the direction of the desired change, install the shims with either the thick side toward the front of the vehicle or toward the rear of the vehicle.

Important: After installing the shims, ensure that the U-bolt has two or three threads above the nut. Ensure also that the center bolt, located in the spring seat, is long enough to seat in the locator hole. If these two conditions do not exist, use longer U-bolts and center bolts. Longer U-bolts and center bolts are available through local spring shops.