General Motors has determined that certain 1989 Chevrolet R/V 2500 Series Suburban trucks equipped with 5.7L engines, built at the Flint Assembly Plant, were shipped without the specified emission (tune-up) label which is required by the Clean Air Act.
To correct this condition, it will be necessary to install a new label on the radiator support.
Since a label can be easily installed and to reduce owner inconvenience, the label will be sent with instructions directly to owners of record. Owners may install the label on the radiator support of their vehicle. However, if they desire, they may bring the label to their servicing Chevrolet Dealer for installation at no charge.
Listed below are the 1989 Chevrolet R/V 2500 Series Suburban Flint assembled trucks involved in the Campaign:
Involved vehicles have been identified by Vehicle Identification Number Computer Listings. Computer listings contain the complete Vehicle Identification Number, owner name and address data, and are furnished to involved dealers with the campaign bulletin. Owner name and address data furnished will enable dealers to follow-up with owners involved in this campaign.
These listings may contain owner names and addresses obtained from State Motor Vehicle Registration Records. The use of such motor vehicle registration data for any other purpose is a violation of law in several states. Accordingly, you are urged to limit the use of this listing to the follow-up necessary to complete this campaign. Any dealer not receiving a computer listing with the campaign bulletin has no involved vehicles currently assigned.
Owners will be notified of this campaign on their vehicies by Chevrolet Motor Division (see copy of owner letter included with this bulletin).
Dealers are to service all vehicles subject to this campaign at no charge to owners, regardless of mileage, age of vehicle, or ownership, from this time forward.
Whenever a vehicle sublect to this campaian is taken into your new or used vehicle inventory, or it is in your dealership for service in the future, you should take the steps necessary to be sure the campaign correction has been made before reselling or releasing the vehicle.
Owners of vehicles recently sold from your new vehicle inventory are to be contacted by the dealer, and arrangements made to make the required correction according to instructions contained in this bulletin.
A new label required for each vehicle involved will be mailed to owners of record and involved dealers (stock units) on a no charge basis.
Part Number Description Quantity/Vehicle ----------- ----------- ---------------- 10123819 Emission Label 1
1. Open hood of vehicle.
2. Using a clean, dry cloth, wipe dirt, oil etc. from the top center of the radiator support (see illustration).
3. Remove backing from the new label and apply to clean panel.
4. Beginning at the center of the label and using a clean, dry cloth, smooth and secure the new label. Any air bubbles can be removed by puncturing with a pin and smoothing with the cloth.
5. Install Campaign Identification Label.
Each vehicle corrected in accordance with the instructions outlined in this bulletin will require a "Campaign Identification Label." Each label provides a space to include the five (5) digit dealer code of the dealer performing the campaign service. This information may be inserted with a typewriter or a ball point pen.
Each "Campaign Identification Label" is to be located on the radiator core support in an area which will be visible when the vehicle is brought in for periodic servicing by the owner.
Apply "Campaign Identification Label" only on a clean dry surface.
CLAIM INFORMATION
Submit a Product Campaign Claim with the information indicated below:
* Failed Parts Labor Lab Oth Repair Performed PC Part No. Allow CC-FC OP Hrs Hrs ----------------- -- -------- ----- ------ -- --- ---
Inspect - previously installed or install label - -- -- SK-00 V5580 0.2 0.1
* Campaign Administrative Allowance
Dealers will automatically receive the correct labor and material allowance based on the labor operation performed.
Refer to the Chevrolet Claims Processing Manual for details on Product Campaign Claim Submission.
This notice is sent to inform you that Chevrolet Motor Division is conducting a recall campaign that includes your vehicle.
REASON FOR THIS RECALL
General Motors has determined that certain 1989 Chevrolet R/V 2500 Series Suburbans equipped with 5.7L engines, and built at the Flint Assembly Plant, were shipped without the specified emission (tune-up) label. Without the correct label, these vehicles do not meet the requirements of the Clean Air Act. WHAT WE WILL DO
To correct this condition, it will be necessary to install a new emission label on the radiator support. Since a label can be easily installed, and to reduce your inconvenience, we are enclosing a label with installation instructions. The label may be installed by you on the radiator support of your vehicle. However, if you desire, your Chevrolet dealer will install the label for you at no charge.
WHAT YOU SHOULD DO
Please let us know if you elect to install the label yourself by completing the enclosed postage paid owner reply card and returning it to us. This assists us in assuring that all affected vehicles have been corrected. If you have sold or traded your vehicle, please let us know by completing the postage paid reply card and returning it to us.
Should you choose to have your local Chevrolet Dealer install the label for you, please bring the owner reply card, along with the enclosed label, to your servicing Chevrolet dealer. Please contact your dealer if you wish to know how much time will be needed to schedule and process your vehicle. Presentation of this card to your dealer will assist in making the necessary correction in the shortest possible time.
We are sorry to cause you this inconvenience; however, we have taken this action in the interest of your continued satisfaction with our products.
LABEL INSTALLATION PROCEDURE
1. Open hood of vehicle.
2. Using a clean, dry cloth: wipe dirt, oil, etc. from top center of the radiator support (see illustration below).
3. Remove backing from the new label and apply to clean panel.
4. Beginning at the center of the label and using a clean, dry cloth, smooth and secure the new label. Any air bubbles can be removed by puncturing with a pin and smoothing with the cloth.
General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.