GM Service Manual Online
For 1990-2009 cars only

Object Number: 190362  Size: MF
Comploc Figure 99 C/K DLC
Power, Ground, and DLC
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The Class 2 Serial Data circuit is used in order to communicate between the control module and the vehicle theft deterrent (VTD) (Passlock) module systems.

When the passlock portion of the VTD system has sensed the proper operation of the ignition switch and lock, or determined that the switch and lock have not been tampered with, the VTD (Passlock) module transmits a password to the control module. Fuel delivery is enabled if this password matches the password stored in the control modules memory. If a component in the theft deterrent system has been replaced, the modules need to relearn the password of the new components. If the relearn procedure was not performed, this diagnostic trouble code (DTC) will set.

If a VTD failure occurs during an ignition cycle that the control module has enabled fuel, then the control module will enter a fail-safe mode: Fail Enable (VTD System Failure with Fuel Enabled). The control module remains in Fail Enable Mode, for the current and future ignition cycles, until the fault is corrected and a valid password is received, or until battery power is removed. If the battery is disconnected or the codes are cleared, the vehicle will lose its Fail Enable status and will not start until the fault is corrected, the ten minute timer expires, and the control module receives the correct fuel delivery password.

Conditions for Running the DTC

    • DTC P1626 is not active
    • The VCM is not in password learn mode
    • The VTD (Passlock) system is enabled.
    • The fuel enable decision point has been reached (engine cranking).

Conditions for Setting the DTC

The VCM did not receive a valid password before the fuel disable decision point was reached.

Action Taken When the DTC Sets

    • The vehicle does not start, or it starts then stalls.
    • A DTC P1631 is stored in the VCM memory.
    • The VCM will not illuminate the MIL.
    • The Security lamp may be illuminated by the VTD (Passlock) system.
    • The VCM disables fuel delivery until the fault is corrected and a valid password is received from the VTD (Passlock) Control Module.

Conditions for Clearing the MIL/DTC

    • A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles.
    • A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant temperature exceeds 70°C (160°F) during the same ignition cycle.
    • Use the scan tool Clear Information function.

Diagnostic Aids

Important: Do not clear DTCs unless directed by a diagnostic procedure. Clearing DTCs will also clear valuable Freeze Frame and Failure Records data.

    • If the VCM is replaced, the VCM must re-learn a valid password and Crankshaft variation.
    • If the VTD (Passlock) Control Module is replaced, the VCM must re-learn a valid password.
    • Check for published service bulletins relating to exhibited symptoms or component operation.
    • If the vehicle does not start, or starts and stalls:
       - Turn OFF the ignition and wait at least 5 seconds before trying to restart.
       - If a fault or tamper has been detected, the VTD module will not forward the correct password to the VCM for a period of ten minutes, even if the condition is corrected during that time period. This may cause a DTC P1631 to set in the VCM. This timer can be monitored in the Passlock Data parameter of the scan tool. Once the time has elapsed, the VTD module will determine if the condition is still present.
    • The VCM's VTD (Passlock) parameters can be monitored with a scan tool.
    • The Passlock state and the auto learn timer can be viewed in the Passlock Data parameter of the scan tool.
    • Check the following for preventing the Passlock sensor from communicating with the VTD (Passlock) Module:
       - Passlock Sensor
       - Ignition switch assembly
       - Passlock Sensor circuitry
       - Bent pins at the small Passlock Sensor
    • If this DTC sets along with a DTC B2960, then the problem was caused by malfunctioning Passlock components or circuitry, not the VCM.
    • Inspect all related wiring and connections including the VCM and VTD (Passlock) Control Module connections. These may cause an intermittent malfunction.

An intermittent may be caused by any of the following conditions:

    • A poor connection
    • Rubbed through wire insulation
    • A broken wire inside the insulation

Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.

If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.

Test Description

Number(s) below refer to the step number(s) on the diagnostic table.

  1. This DTC may set as a result of other Passlock System problems. Diagnose any VTD (Passlock) DTCs prior to continuing with this diagnostic.

  2. A DTC B3031 may set in the VTD (Passlock) Module during the Password Learn Procedure.

Step

Action

Value(s)

Yes

No

1

Important: Before clearing the DTCs, use the scan tool Capture Info to save the Freeze Frame and Failure Records for reference. The control module's data is deleted once the Clear Info function is used.

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

  1. Turn ON the ignition leaving the engine OFF.
  2. Observe the Vehicle Theft Deterrent (VTD) (Passlock) DTC display using the scan tool.

Are any VTD (Passlock) DTCs displayed?

--

Go to Diagnostic System Check - Theft Deterrent in Theft Deterrent

Go to Step 3

3

Perform the Passlock Reprogramming Procedure. Refer to PASSLOCK Reprogramming Auto Learn in Theft Deterrent.

Did the VCM successfully learn the password?

--

Go to Step 4

Go to Diagnostic System Check - Theft Deterrent in Theft Deterrent

4

Important:: Before Clearing DTCs, monitor all DTC status parameters and note any additional DTCs.

  1. Clear VCM DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Attempt to start the engine.

Does the engine start and operate normally?

--

System OK

Go to Step 2