Air Conditioning Evaporator Thermal Expansion Valve Screen Replacement C60

Tools Required

J 39400-A Halogen Leak Detector

Important: The A/C Refrigerant filter, ACDelco P/N 15-1696 must be installed to the A/C evaporator tube between the condenser and evaporator. The installation of this A/C refrigerant filter eliminates the need for flushing.

1. Remove the air cleaner. Refer to Air Cleaner Assembly Replacement in Engine Controls.
2. Measure 50 mm (2 in) from the bend on the evaporator tube (2) near the expansion tube end and mark the location.
3. Measure 50.8 mm (2 in) from the mark on the evaporator tube (2) from the previous step.

Important: Do not allow metal burrs to enter the evaporator tube (2) during cutting or when removing the burrs.

4. Using a tubing cutter, cut the marked section of the evaporator tube (2).
5. Remove the burrs from the evaporator tube (2).



6. Remove the nuts (4), the ferrules (3), and the O-rings (2) from the A/C refrigerant filter (1).

Important: DO NOT install the O-rings (2) in this step.

7. Push the nuts (4) and ferrules (3) over each of the evaporator tube halves.
8. Install the ferrules (3) with the small end toward the nut (4).



9. Install the A/C refrigerant filter (3) to the evaporator tube (2) with the flow arrow pointing towards the evaporator.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

10. While holding the evaporator tube in the A/C refrigerant filter (1), tighten the nuts (4) to the A/C refrigerant filter (1).

Tighten
Tighten the nuts to 15 N·m (11 lb ft).

11. Remove the nuts (4) from the A/C refrigerant filter (1).
12. Coat the O-rings (2) with 525 viscosity refrigerant oil.
13. Install the O-rings (2) to the evaporator tube halves.
14. Install the nuts (4) to the A/C refrigerant filter (1).

Tighten
Tighten the nuts to 15 N·m (11 lb ft).

15. Evacuate and recharge the system. Refer to Refrigerant Recovery and Recharging .
16. Leak test the fittings of the component using the J 39400-A .
17. Install the air cleaner. Refer to Air Cleaner Assembly Replacement in Engine Controls.

Air Conditioning Evaporator Thermal Expansion Valve Screen Replacement C69

Tools Required

J 39400-A Halogen Leak Detector

Important: The A/C refrigerant filter, ACDelco P/N 15-1696 must be installed to the A/C evaporator tube (liquid line) between the condenser and evaporator. The installation of this A/C refrigerant filter eliminates the need for flushing.

1. Remove the air cleaner. Refer to Air Cleaner Assembly Replacement in Engine Controls.



2. Remove the evaporator tube (2) from the vehicle. Refer to Evaporator Tube Replacement .
3. Measure 45 mm (1.75 in) from the bend on the condenser end of the evaporator tube (2) and mark the location.
4. Measure 50.8 mm (2 in) from the mark on the evaporator tube (2) towards the evaporator from the previous step.

Important: Do not allow metal burrs to enter the evaporator tube (2) during cutting or when removing the burrs.

5. Using a tubing cutter, cut the marked section of the evaporator tube (2).
6. Remove the burrs from the evaporator tube (2).



7. Remove the nuts (4), the ferrules (3), and the O-rings (2) from the A/C refrigerant filter (1).

Important: Do Not install the O-rings (2) in this step.

8. Push the nuts (4) and ferrules (3) over each of the evaporator tube halves.
9. Install the ferrules (3) with the small end toward the nut (4).



10. Install the A/C refrigerant filter (3) to the evaporator tube (2) with the flow arrow pointing towards the evaporator.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

11. While holding the evaporator tube in the A/C refrigerant filter (1), tighten the nuts (4) to the A/C refrigerant filter (1).

Tighten
Tighten the nuts to 15 N·m (11 lb ft).

12. Remove the nuts (4) from the A/C refrigerant filter (1).
13. Coat the O-rings (2) with 525 viscosity refrigerant oil.
14. Install the O-rings (2) to the evaporator tube halves.
15. Install the nuts (4) to the A/C refrigerant filter (1).

Tighten
Tighten the nuts to 15 N·m (11 lb ft).




16. Install the evaporator tube (2) to the vehicle. Refer to Evaporator Tube Replacement .
17. Evacuate and recharge the system. Refer to Refrigerant Recovery and Recharging .
18. Leak test the fittings of the component using the J 39400-A .
19. Install the air cleaner. Refer to Air Cleaner Assembly Replacement in Engine Controls.