GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2002 🢒 Chevy Suburban - 2WD 🢒 Engine 🢒 Engine Exhaust 🢒 Exhaust Muffler Replacement

Exhaust Muffler Replacement 4.8L and 5.3L Engines

Tools Required

J 38185 Hose Clamp Pliers

Removal Procedure

    Object Number: 339429 Size: SH
  1. Remove the rear tires and wheels. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  2. Remove the oil pan skid plate bolts and plate, if necessary.
  3. Remove the spare tire.

    4. Object Number: 665311 Size: SH
  4. If servicing a vehicle equipped with regular production option (RPO) Z55, disconnect the chassis harness from the following electrical connectors:
    5. • Electronic suspension rear position sensor (1)
    • Rear shock (2)

    Important: Do not attempt to pry the rear suspension sensor link rod from the rear position sensor ball stud.

  5. Remove the left and right sensor link rods from the sensors, perform the following:
    6. 5.1. Support the sensor lever with your hand
    5.2. Twist the link rod in order to remove it from the ball stud
  6. Install adjustable jack stands under the rear axle.

    7. Object Number: 692548 Size: SH
  7. Remove the rear axle vent hose from the rear axle, if necessary.
  8. Remove the vent hose swivel clip from the rear brake crossover pipe.

    9. Object Number: 665315 Size: SH
  9. Remove the rear shock absorbers lower bolts and nuts.
  10. Lower the rear axle slightly, using the adjustable jack stands, in order to remove the muffler.

    11. Object Number: 664840 Size: SH
  11. Remove the exhaust muffler nuts.

    12. Object Number: 665327 Size: SH
  12. Remove the muffler from the insulators.

Installation Procedure

    Object Number: 665327 Size: SH
  1. Apply lubricant to the exhaust insulators in order to aid in installation.
  2. Install the muffler to the insulators.

    3. Object Number: 664840 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the exhaust muffler nuts.

    4. Tighten
    Tighten the nuts to 40 N·m (30 lb ft).


    Object Number: 665315 Size: SH
  4. Raise the rear axle, using the adjustable jackstands.
  5. Install the lower bolts and nuts to the rear shock absorbers.

    6. Tighten
    Tighten the rear bolts to 95 N·m (70 lb ft).

  6. Remove the adjustable jack stands from under the rear axle.

    7. Object Number: 692548 Size: SH
  7. Install the vent hose swivel clip to the rear brake crossover pipe.
  8. Install the rear axle vent hose to the rear axle, if necessary.

    9. Object Number: 665311 Size: SH
  9. If servicing a vehicle, equipped with RPO Z55, install the left and right sensor link rods to the sensors. Using J 38185 install the link rods to the ball studs on the sensor levers.
  10. Connect the chassis harness to the following electrical connectors:
    11. • Electronic suspension rear position sensor (1)
    • Rear shock (2)
  11. Install the spare tire.

    12. Object Number: 339429 Size: SH
  12. Install the oil pan skid plate and bolts, if necessary.

    13. Tighten
    Tighten the bolts to 20 N·m (15 lb ft).

  13. Install the rear tires and wheels. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.

Exhaust Muffler Replacement 6.0L and 8.1L Engines

Tools Required

J 38185 Hose Clamp Pliers

Removal Procedure

    Object Number: 339429 Size: SH
  1. Remove the rear tires and wheels. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  2. Remove the oil pan skid plate bolts and plate, if necessary.
  3. Remove the spare tire.

    4. Object Number: 665311 Size: SH
  4. If servicing a vehicle with regular production option (RPO) Z55, disconnect the chassis harness from the following electrical connectors:
    5. • Electronic suspension rear position sensor (1)
    • Rear shock (2)

    Important: Do not attempt to pry the rear suspension sensor link rods from the rear position sensor ball studs.

  5. Remove the left and right sensor link rods from the sensors, perform the following:
    6. 5.1. Support the sensor lever with your hand
    5.2. Twist the link rod in order to remove it from the ball stud
  6. Install adjustable jack stands under the rear axle.

    7. Object Number: 692548 Size: SH
  7. If equipped with a 8.6 or 9.5 inch ring gear, remove the rear axle vent hose from the rear axle, if necessary.
  8. Remove the vent hose swivel clip from the rear brake crossover pipe.

    9. Object Number: 695038 Size: SH
  9. If equipped with a 10.5 inch ring gear, remove the rear axle vent hose from the rear axle, if necessary.
  10. Remove the vent hose swivel clip from the rear brake crossover pipe.

    11. Object Number: 665315 Size: SH
  11. Remove the rear shock absorbers lower bolts and nuts.
  12. Lower the rear axle slightly, using the adjustable jack stands, in order to remove the muffler.

    13. Object Number: 693000 Size: SH
  13. Unclip the oxygen sensor connector from the frame.
  14. Disconnect the connector position assurance (CPA) retainer.
  15. Disconnect the oxygen sensor electrical connector.

    16. Object Number: 694898 Size: SH
  16. Unclip the oxygen sensor connector from the support.
  17. Disconnect the CPA retainer.
  18. Disconnect the oxygen sensor electrical connector.

    19. Object Number: 694902 Size: SH
  19. Unclip the oxygen sensor connector from the support.
  20. Disconnect the CPA retainer.
  21. Disconnect the oxygen sensor electrical connector.

    22. Object Number: 694907 Size: SH
  22. If equipped with a 6.0L engine, perform the following:
    23. • Unclip the oxygen sensor connector from the frame.
    • Disconnect the CPA retainer.
    • Disconnect the oxygen sensor electrical connector.

    Object Number: 665520 Size: SH
  23. Remove the exhaust muffler nuts.
  24. Loosen the exhaust pipe clamp.
  25. With the aid of an assistant, support the exhaust muffler.

    26. Object Number: 665522 Size: SH
  26. Remove the insulators from the frame hangers.
  27. With the aid of an assistant, slide the muffler rearward in order to remove the muffler from the catalytic converter.
  28. Remove the insulators from the muffler hangers.
  29. Remove the exhaust manifold pipe gasket.

    30. Object Number: 695550 Size: SH
  30. Remove the oxygen sensor if the muffler is being replaced.

Installation Procedure

    Object Number: 695550 Size: SH
  1. If the muffler was replaced reinstall the old oxygen sensor.
  2. Apply anti-seize compound GM P/N 12377953 or equivalent to the threads of the old oxygen sensor.

    3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the oxygen sensor.

    4. Tighten
    Tighten the oxygen sensor to 42 N·m (31 lb ft).


    Object Number: 665522 Size: SH

    Important: Apply lubricant to the insulators to aid in installation.

  4. Install the insulators to the muffler hangers.
  5. Install a new exhaust manifold pipe gasket.
  6. With the aid of an assistant, slide the muffler forward in order to install the muffler to the catalytic converter.
  7. Install the insulators to the frame hangers.

    8. Object Number: 665520 Size: SH
  8. Install the exhaust muffler nuts, until snug.
  9. Tighten the exhaust pipe clamp bolt and muffler nuts.

    10. Tighten

        • Tighten the exhaust muffler nuts to 40 N·m (30 lb ft).
        • Tighten the exhaust pipe clamp to 40 N·m (30 lb ft).

    Object Number: 694907 Size: SH
  10. If equipped with a 6.0L engine, perform the following:
    11. • Connect the oxygen sensor electrical connector.
    • Connect the CPA retainer.
    • Clip the oxygen sensor connector to the frame.

    Object Number: 694902 Size: SH
  11. Connect the oxygen sensor electrical connector.
  12. Connect the CPA retainer.
  13. Clip the oxygen sensor connector to the support.

    14. Object Number: 694898 Size: SH
  14. Connect the oxygen sensor electrical connector.
  15. Connect the CPA retainer.
  16. Clip the oxygen sensor connector to the support.

    17. Object Number: 693000 Size: SH
  17. Connect the oxygen sensor electrical connector.
  18. Connect the CPA retainer.
  19. Clip the oxygen sensor connector to the frame.

    20. Object Number: 665315 Size: SH
  20. Raise the rear axle using the adjustable jack stands.
  21. Install the rear shock absorbers lower bolts and nuts.

    22. Tighten
    Tighten the lower bolts to 95 N·m (70 lb ft).

  22. Remove the adjustable jack stands from under the rear axle.

    23. Object Number: 695038 Size: SH
  23. If equipped with a 10.5 inch ring gear, connect the vent hose swivel clip to the rear brake crossover pipe.
  24. Install the rear axle vent hose to the rear axle, if necessary.

    25. Object Number: 692548 Size: SH
  25. If equipped with a 8.6 or 9.5 inch ring gear, connect the vent hose swivel clip to the rear brake crossover pipe.
  26. Install the rear axle vent hose to the rear axle, if necessary.

    27. Object Number: 665311 Size: SH
  27. If servicing a vehicle equipped with RPO Z55, install the left and right sensor link rods to the sensors. Using J 38185 install the link rods to the ball studs on the sensor levers.
  28. Connect the chassis harness to the following electrical connectors:
    29. • Electronic suspension rear position sensor (1)
    • Rear shock (2)
  29. Install the spare tire.

    30. Object Number: 339429 Size: SH
  30. Install the oil pan skid plate and bolts, if necessary.

    31. Tighten
    Tighten the bolts to 20 N·m (15 lb ft).

  31. Install the rear tires and wheels. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.