Schematic Reference: Sunroof Schematics

Connector End View Reference: Power Roof Systems Connector End Views

Did you perform the Power Sunroof Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Power Sunroof

Perform the sunroof re-initialization. Refer to Sunroof Motor/Actuator Synchronization .

Does the system operate normally?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

1. Disconnect the sunroof switch harness connector.
2. Turn ON the ignition, with the engine OFF.
3. Connect a test lamp between the retained accessory power (RAP) relay switched output circuit at the sunroof switch harness connector and a good ground.

Does the test lamp illuminate?

Go to Step 4

Go to Step 10

1. Connect a fused jumper wire to the RAP relay switched output circuit at the sunroof switch harness connector.
2. Observing the position of the sunroof glass, try to operate the sunroof system by connecting the other end of the fused jumper wire, at the sunroof switch harness connector, to either of the following:

•	The sunroof switch open/tilt down signal circuit

•	The sunroof switch close/tilt upn signal circuit

Does the system operate normally?

Go to Step 11

Go to Step 5

Test the sunroof switch open/tilt down signal circuit for an open, or a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 6

Test the sunroof switch close/tilt upn signal circuit for an open, or a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 7

1. Connect the sunroof switch harness connector.
2. Disconnect the sunroof module harness connector.
3. Connect a test lamp between the RAP relay switched output circuit at the sunroof module harness connector and a good ground.

Does the test lamp illuminate?

Go to Step 8

Go to Step 10

Connect a test lamp between the battery positive voltage circuit at the sunroof module harness connector and a good ground.

Does the test lamp illuminate?

Go to Step 9

Go to Step 13

Connect a test lamp between the battery positive voltage circuit and ground circuit at the sunroof module harness connector.

Does the test lamp illuminate?

Go to Step 12

Go to Step 14

Test the RAP relay switched output circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Retained Accessory Power (RAP) Inoperative in Retained Accessory Power

Inspect for a poor connections at the sunroof switch harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems?

Did you find and correct the condition?

Go to Step 17

Go to Step 15

Inspect for a poor connection at the sunroof module harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 16

Repair the open in the battery positive voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 17

--

Repair the open in the sunroof module ground circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 17

--

Replace the sunroof switch. Refer to Sunroof Switch Replacement .

Did you complete the replacement?

Go to Step 17

--

Replace the sunroof module. Refer to Sunroof Motor/Actuator Replacement .

Did you complete the replacement?

Go to Step 17

--

1. Turn OFF the ignition.
2. Remove any jumper wires.
3. Reconnect all previously disconnected components.
4. Replace the fuse if necessary.
5. Re-initialize the sunroof. Refer to Sunroof Motor/Actuator Synchronization .
6. Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2