For a view of the oil flow diagrams, refer to the 1996 TURM manual.

In order to obtain third gear, the PCM receives input signals from the VSS, from the TP Sensor, and from other engine sensors. These signals determine when to energize solenoid B.

Manual Valve: In the Overdrive range third gear, line pressure from the pressure regulator valve is directed as PRND4, PRND43, and Drive fluid pressures. The PRND4 fluid pressure is directed to the Automatic Transmission Fluid Pressure Manual Valve Position Switch (TFP Val. Position Sw.) Assembly and to the 2-3 shift valve. The PRND43 fluid is directed to the TFP Val. Position Sw. Assembly and to the front servo. The Drive fluid is directed to the TFP Val. Position Sw. assembly, and the forward clutch.

Automatic Transmission Fluid Pressure Manual Valve Position Switch: Drive, PRND4, and PRND43 fluid pressures from the manual valve are directed to the DR, PRND4, and the PRND43 switches on the TFP Val. Position Sw. Assembly. This sends a signal to the PCM that the transmission is in Overdrive range.

1-2 Shift Solenoid (1-2 SS) Valve: When the 1-2 SS Valve is de-energized, signal A fluid exhausts through the solenoid. A spring force holds the 3-4 shift valve to the extreme right.

2-3 Shift Solenoid (1-2 SS) Valve: When the 2-3 SS Valve is energized, signal B fluid pressure forces the 1-2 shift valve to the extreme right against a spring force.

1-2 Shift Valve: Spring force and signal B fluid pressure hold the 1-2 Shift Valve to the extreme right. Drive fluid pressure from the manual valve changes into 2-3 drive fluid pressure at the 1-2 shift valve. This pressure is directed to the 2-3 shift valve, to the TCC PWM Solenoid Valve, and to the intermediate (second) clutch.

2-3 Shift Valve: The PRND4 fluid pressure from the manual valve is directed through the 2-3 shift valve, to the 3-4 shift valve. The PRND4 fluid pressure changes into Fourth clutch fluid pressure at the 2-3 shift valve. The 2-3 DR fluid pressure from the 1-2 shift valve is changed into Third clutch fluid pressure at the 2-3 shift valve. This seats the #8 checkball, causing the fluid to flow through an orifice and toward the third accumulator. Third clutch fluid pressure also seats the #11 checkball, causing the fluid to flow through an orifice and toward the direct clutch.

3-4 Shift Valve: Fourth clutch fluid pressure is blocked at the 3-4 shift valve, where the pressure is utilized in Overdrive range fourth gear.

Forward Clutch: Drive fluid pressure from the manual valve applies the forward clutch.

Intermediate (Second) Clutch: Second fluid pressure from the 1-2 shift valve applies the intermediate clutch. The 2-3 drive fluid pressure from the 1-2 shift valve seats the #4 checkball, causing the fluid to flow through two orifices and into the center support. This applies the Intermediate (Second) clutch. The 2-3 drive fluid pressure changes into Second apply fluid pressure at the orifices.

Direct Clutch: Third/Reverse pressure from the #11 checkball flows through the case and through the center support in order to apply the inner piston area of the direct clutch.

Third Clutch Accumulator: Third clutch fluid pressure is also applied to the third clutch accumulator, which is encased in the accumulator housing. This moves the third accumulator piston against the spring force and accumulator fluid pressure.

Torque Converter Clutch Pulse Width Modulated (TCC PWM) Solenoid: The PCM energizes the TCC PWM, and pressure is applied to the converter clutch shift valve. The Torque Converter Clutch (TCC) is applied. The signal pressure also acts on the torque converter clutch regulator valve, which regulates the output pressure. This controls the apply and release of the TCC.