Circuit Description
The optical sensor provides a pump cam signal to the PCM by counting pulses on the sensor disk located in the injection pump. The pump cam is one of the most important inputs by the PCM for fuel control and timing. This test monitors the number of crankshaft position pulses that have occurred since the last cam pulse. The physical one to one correspondence between the pump cam and the crankshaft implies if more crank pulses are detected than cam pulses, cam pulses have been missed. This is a type A DTC.
Conditions for Setting the DTC
| • | RPM less than 300. |
| • | 8 consecutive cam pulses missing for 8 #1 cylinder events. |
or
| • | RPM greater than or equal to 300. |
| • | 8 consecutive cam pulses missing for 32 #1 cylinder events. |
Action Taken When the DTC Sets
Backup fuel.
Conditions for Clearing the MIL/DTC
| • | The PCM will turn the MIL off after three consecutive trips without a fault condition. |
| • | A History DTC will clear when forty consecutive warm-up cycles that the diagnostic does not fail (coolant temperature has risen 5°C (40°F) from start up coolant temperature and engine coolant temperature exceeds 71°C (160°F) that same ignition cycle. |
| • | Use of a Scan Tool |
Diagnostic Aids
When PCM is in backup fuel, fast idle and poor performance problems will exist. If P0251 is also stored, there is a possible problem with signal circuit. P0251 and P0370 will set if vehicle has run out of fuel.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
-
This step will determine if this is a hard or intermittent DTC.
-
This step will determine if there is a 5 volt reference.
-
This step will check to see if the sensor is sending a signal back to the PCM.
-
The PCM supplies 5 volts on the signal circuit. This step determines if that voltage is present, not present, or too much voltage is present.
-
This step determines if the signal circuit is shorted to 5V. A normal CAM signal circuit will have 3-5mA. Any reading over 50mA indicates a short to 5V.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 |
Important: Before clearing any DTCs, use the scan tool Capture Info to save freeze frame and failure records for reference, as the scan tool loses data when using the Clear Info function. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
2 | Is the DTC P0370 set also? | -- | Go to DTC P0370 Timing Reference High Resolution System Performance | |
Does scan tool display the specified value? | 8 | |||
4 | The DTC is intermittent. If no additional DTCs are stored, refer to Diagnostic Aids. If additional DTCs were stored refer to the applicable DTC table(s) first. Are any additional DTCs stored? | -- | Go to the Applicable DTC Table | Go to Diagnostic Aids |
Is the voltage within the specified value? | 4.8-5.2V | |||
6 | Probe the sensor ground circuit with a test light connected to B+ at the harness connector. Is the test light ON? | -- | ||
Is the Hertz reading at the specified value? | 60 Hz (± 3 Hz) | |||
8 |
Is the resistance greater than the specified value? | 2 ohms | ||
9 |
Was the Optical sensor 5 volt reference circuit open or shorted to ground? | -- | ||
10 |
Was a repair performed? | -- | ||
11 | Check the Optical/Fuel temperature 5 volt reference circuit for a proper connection at the PCM and replace terminal if necessary. Did the terminal require replacement? | -- | ||
Is the voltage within the specified value? | 4.8-5.2V | |||
13 | Is the voltage greater than the specified value? | 4.8-5.2V | ||
14 | Repair the short to battery/ignition voltage on the CAM signal circuit. Is the action complete? | -- | -- | |
15 |
Was the CAM signal circuit open or shorted to ground? | -- | ||
16 | Check for a proper connection at the PCM harness terminal and replace the terminal if necessary. Did the terminal require replacement? | -- | ||
With a DMM J 39200 set to the mA scale, measure the current between the CAM signal circuit and the ground circuit at the Optical/Fuel temperature sensor electrical connector. Is the current less than the specified value? | 50mA | |||
18 | Repair the short to reference voltage on the CAM signal circuit. Is the action complete? | -- | -- | |
19 |
Was a problem found? | -- | ||
20 | Replace the electrical filter harness. Is the action complete? | -- | -- | |
21 | Replace the injection pump. Refer to Fuel Injection Pump Replacement . Important: The new injection pump must be timed. Refer to Checking/Adjust Injection Timing . Is the action complete? | -- | -- | |
22 | Replace the PCM. Important: The new PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Is the action complete? | -- | -- | |
23 |
Does the Scan tool indicate the diagnostic Passed? | -- | ||
24 | Does the Scan tool display any additional undiagnosed DTCs? | -- | Go to the Applicable DTC Table | System OK |
