Tools Required

J 21366 Converter Holding Strap

1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Drain the transmission fluid. Refer to Automatic Transmission Fluid and Filter Replacement .
3. Remove the rear propeller shaft. Refer to Rear Propeller Shaft Replacement in Propeller Shaft.
4. Support the transmission with a suitable jack.
5. Remove the transmission support. Refer to Transmission Support Replacement in Frame and Underbody.
6. Remove the exhaust manifold pipe. Refer to Exhaust Manifold Pipe Replacement in Engine Exhaust.
7. Remove the transmission mount. Refer to Transmission Mount Replacement .
8. Remove the transfer case, if equipped. Refer to Transfer Case Assembly Replacement in Transfer Case NVG 149-NP (One Speed Automatic) or Transfer Case Assembly Replacement in Transfer Case NVG 236/246-NP8 (Two Speed Automatic).



9. Remove the range selecter cable from the transmission range selecter lever ball stud and bracket. Refer to Range Selector Lever Cable Replacement .
10. Disconnect the electrical harness from the park/neutral position switch, the input speed sensor, and the output speed sensor.
11. Disconnect the wire harness from the wire loom on the left side of the transmission.
12. Cut the tie strap to separate the vent hose from the wiring harness.



13. Remove the flywheel inspection cover.
14. Mark the torque converter to flywheel orientation.
15. Remove the torque converter bolts.



16. Remove the transmission heat shield. Refer to Transmission Heat Shield Replacement .



17. Disconnect the transmission oil cooler lines from the transmission. Refer to Transmission Fluid Cooler Hose/Pipe Replacement .
18. Plug the transmission oil cooler line connectors in the transmission case.



19. Remove the stud and the bolt on the right side securing the transmission to the engine.



20. Remove the remaining six studs and the one bolt securing the transmission to the engine.
21. Install the J 21366 onto the transmission bell housing to retain the torque converter.
22. Pull the transmission straight back.
23. Remove the transmission from the vehicle.
24. Flush the transmission oil cooler and lines at this time. Refer to Transmission Fluid Cooler Flushing and Flow Test .

1. Install the J 21366 onto the transmission bell housing to retain the torque converter.
2. Raise the transmission into place and remove the J 21366 from the transmission.
3. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must rotate freely by hand.

Notice: Refer to Fastener Notice in the Preface section.

4. Install studs and bolt securing the transmission to the engine.

Tighten
Tighten the studs and the bolt to 50 N·m (37 lb ft).




5. Install the stud and bolt on the right side securing the transmission to the engine.

Tighten
Tighten the stud and the bolt to 50 N·m (37 lb ft).




6. Line up the marks made during removal and install the flywheel to torque converter bolts.

Tighten
Tighten the bolts to 60 N·m (44 lb ft).

7. Install the torque converter cover to the transmission.
8. Install the bolts securing the torque converter cover.

Tighten
Tighten the bolts to 33 N·m (24 lb ft).




9. Install the vent hose to the wiring harness using a new tie strap.
10. Connect the wiring harness to the wiring loom on the left side of the transmission.
11. Connect the electrical harness to the park/neutral position switch, the input speed sensor, and the output speed sensor.
12. Install the range selecter cable to the transmission range selecter lever ball stud and bracket. Refer to Range Selector Lever Cable Replacement .



13. Install the transfer case, if equipped. Refer to Transfer Case Assembly Replacement in Transfer Case NVG 149-NP (One Speed Automatic) or Transfer Case Assembly Replacement in Transfer Case NVG 236/246-NP8 (Two Speed Automatic).
14. Install the transmission mount. Refer to Transmission Mount Replacement .
15. Install the exhaust manifold pipe. Refer to Exhaust Manifold Pipe Replacement in Engine Exhaust.
16. Install the transmission support. Refer to Transmission Support Replacement in Frame and Underbody.
17. Remove the transmission jack.
18. Install the rear propeller shaft. Refer to Rear Propeller Shaft Replacement in Propeller Shaft.



19. Connect the transmission oil cooler lines to the transmission. Refer to Transmission Fluid Cooler Hose/Pipe Replacement .



20. Install the transmission heat shield.
21. Install the bolts securing the heat shield to the transmission.

Tighten
Tighten the bolts to 17 N·m (13 lb ft).

22. Lower the vehicle.
23. Fill the transmission to the proper level with DEXRON® VI transmission fluid. Refer to Transmission Fluid Check .

Important: It is recommended that transmission adaptive pressure (TAP) information be reset.

Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.
24. Reset the TAP values. Refer to Adapt Function .