GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2002 🢒 Chevy Suburban - 4WD 🢒 Body and Accessories 🢒 Instrument Panel, Gages, and Console 🢒 Chime Inoperative

Step

Action

Value(s)

Yes

No

Schematic Reference: Audible Warnings Schematics

DEFINITION: One or more chime functions are inoperative.

1

Did you perform the Audible Warning Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Audible Warnings

2
  1. Turn the ignition OFF, with the key in the ignition.
  2. Open the driver door.

Does the chime sound?

--

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3
  1. Install a scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. Open the driver door.
  4. With the scan tool, observe the Driver Door Jamb Switch parameter in the BCM Input 1 data list.

Does the Driver Door Jamb Switch parameter display ACTIVE?

--

Go to Step 7

Go to Step 4

4
  1. Turn the ignition OFF.
  2. Disconnect the driver door jamb switch connector.
  3. Connect a 3 amp fused jumper wire between the signal circuit of the driver door jamb switch and a good ground.
  4. Turn the ignition ON, with the engine OFF.
  5. With the scan tool, observe the Driver Door Jamb Switch parameter in the BCM Input 1 data list.

Does the Driver Door Jamb Switch parameter display ACTIVE?

--

Go to Step 6

Go to Step 5

5

Test the driver door jamb switch signal circuit for an open or for a high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 10

6

Test the driver door jamb switch ground circuit for an open or for a high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 8

7
  1. Turn the ignition ON, with the engine OFF.
  2. With the scan tool, observe the Key In Ignition parameter in the BCM Input 1 data list.

Does the Key In Ignition parameter display YES?

--

Go to Step 10

Go to Step 9

8

Inspect for poor connections at the harness connector of the driver door jamb switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 11

9

Inspect for poor connections at the harness connector of the ignition key alarm switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 12

10

Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 13

11

Replace the driver door jamb switch. Refer to Front Side Door Lock Actuator Replacement in Doors.

Did you complete the replacement?

--

Go to Step 14

--

12

Replace the ignition key alarm switch. Refer to:

    •  Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle in Steering Wheel and Column

Did you complete the replacement?

--

Go to Step 14

--

13

Important: Perform the set up procedure for the replacement BCM.

Replace the BCM. Refer to Body Control Module Replacement in Body Control System.

Did you complete the replacement?

--

Go to Step 14

--

14
  1. Use the scan tool in order to clear the BCM DTCs.
  2. Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 2