Starter Replacement 8.1L Engine
Removal Procedure
- Disconnect the negative battery cable.
Refer to
Battery Negative Cable Disconnection and Connection
.
- Raise and suitably support the vehicle. Refer to
Lifting and Jacking the Vehicle
in General Information.
- If equipped with four wheel drive (4WD), remove the front axle mounting
bracket nuts.
Important: DO NOT remove the bolt.
- If equipped with 4WD, reposition the front axle mounting bracket bolt until
the bolt tip is flush with the support bushing.
- Remove the starter bolts.
- Slide the starter forward until the starter clears the transmission.
- Remove the starter lead nut.
- Remove the starter lead (4) from the starter.
- Remove the positive cable nut.
- Remove the positive cable from the starter.
- If necessary, remove the starter heat
shield bolts, nut, and shield.
Installation Procedure
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- If necessary, install the starter heat shield, nut and bolts.
Tighten
• | Tighten the bolts to 3 N·m (35 lb in). |
• | Tighten the nut to 5 N·m (44 lb in). |
- Install the positive cable to the starter.
- Install the positive cable nut.
Tighten
Tighten the nut to 9 N·m (80 lb in).
- Install the starter lead (4) to the starter.
- Install the starter lead nut.
Tighten
Tighten the nut to 3.4 N·m (30 lb in).
- Position the starter into place.
- Install the starter bolts.
Tighten
Tighten the bolts to 50 N·m (37 lb ft).
- If equipped with 4WD, position the front
axle mounting bracket bolt until the bolt is fully seated.
- If equipped with 4WD, install the front axle mounting bracket nuts.
Tighten
Tighten the nuts to 95 N·m (70 lb ft).
- Lower the vehicle.
- Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
Starter Replacement 4.8L, 5.3L, and 6.0L Engines
Removal Procedure
- Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
- Remove the engine oil level indicator tube fasteners and position aside. Refer to
Oil Level Indicator and Tube Replacement
.
- Raise and suitably support the vehicle. Refer to
Lifting and Jacking the Vehicle
in General Information.
- Remove the transmission cover bolt.
- If equipped with four wheel drive (4WD), remove the front axle mounting bracket nuts.
Important: DO NOT remove the bolt.
- If equipped with 4WD, reposition the front axle mounting bracket bolt until the bolt tip is flush with the support bushing.
- Remove the starter bolts.
- Disconnect the oil level sensor electrical connector.
- Slide the starter forward until the starter clears the transmission.
- Remove the starter lead nut (3).
- Remove the starter lead (2) from the starter.
- Remove the positive cable nut (1).
- Remove the positive cable from the starter.
- Place the starter on a workbench.
- If necessary, unsnap the transmission cover from the starter.
- If necessary, remove the starter heat shield.
Installation Procedure
- If necessary, install the starter heat shield.
- If necessary, snap the transmission cover to the starter.
Notice: Refer to Fastener Notice in the Preface section.
- Install the positive cable to the starter.
- Install the positive cable nut (1).
Tighten
Tighten the nut to 9 N·m (80 lb in).
- Install the starter lead (2) to the starter.
- Install the starter lead nut (3).
Tighten
Tighten the nut to 3.4 N·m (30 lb in).
- Position the starter into place.
- Install the starter bolts.
Tighten
Tighten the bolts to 50 N·m (37 lb ft).
- Connect the oil level sensor electrical connector.
- If equipped with 4WD, position the front axle mounting bracket bolt until the bolt is fully seated.
- If equipped with 4WD, install the front axle mounting bracket nuts.
Tighten
Tighten the nuts to 95 N·m (70 lb ft).
- Install the transmission cover bolt.
Tighten
Tighten the bolt to 9 N·m (80 lb in).
- Lower the vehicle.
- Install the engine oil level indicator tube. Refer to
Oil Level Indicator and Tube Replacement
.
- Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.