Circuit Description
The powertrain control module (PCM) uses the following readings in order to calculate the predicted mass air flow (MAF) rate:
| • | The throttle position (TP) |
| • | The barometric (BARO) pressure |
| • | The intake air temperature (IAT) |
| • | The engine RPM |
The PCM compares the predicted MAF value to the actual MAF value, and to the speed density calculation in order to verify the proper throttle operation.
Conditions for Running the DTC
| • | DTCs P0601, P0602, P0604, P0606, P1515, P1516, P1517, or P1518 are not set. |
| • | The following DTCs are not active at the same time: |
| P1120, P1220, P1221 |
| • | The following DTCs are not active at the same time: |
| P1120 and P1220 |
| • | The engine operates longer than 1 second. |
| • | The engine speed is more than 500 RPM. |
Conditions for Setting the DTC
| • | The PCM detects that the difference between the actual airflow (MAF) and the Speed Density calculated air flow is more than expected. |
| • | The above condition is met for less than 1 second. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Inspect the throttle blade for being broken, bent, or missing. |
| • | Inspect the throttle position (TP) sensor for proper installation. A sensor that is mis-aligned could set this DTC. |
| • | Inspect the throttle actuator control (TAC) module connectors for signs of water intrusion. If water intrusion occurs, multiple DTCs may set without any circuit or component conditions found during diagnostic testing. |
| • | Physically and visually inspect the throttle body assembly and correct any problems that you observe. Manually move the throttle blade from closed to wide open throttle (WOT). You should not need to use excess force. The throttle blade should move smoothly through the full range and then should independently return to a slightly open position. |
| • | When the TAC module detects a condition within the TAC system, more than 1 TAC system related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing 1 individual condition may correct more than 1 DTC. Disconnecting components during testing may set additional DTCs. Remember this if you review the stored information in Capture Info. |
| • | For an Intermittent condition, refer to Intermittent Conditions . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step will determine if the manifold absolute pressure (MAP) sensor voltage is within the proper range at idle.
-
This step will determine if the MAP sensor responds properly to the change in manifold pressure.
-
A throttle blade that sticks or binds may set this code. Opening the throttle through the entire range will indicate problems such as these.
-
When the PCM detects a condition within the ETC system other DTCs may set due to the many redundant tests run continuously on this system. Locating and repairing 1 individual condition may correct more than 1 DTC. Keep this in mind when reviewing captured DTC info.
Step | Action | Values | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views | ||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||||
2 | Are any other DTCs set? | -- | Go to Step 3 | |||||||
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids | ||||||
4 | Inspect for the following conditions:
Did you find and correct the condition? | -- | Go to Step 8 | Go to Step 5 | ||||||
Is the MAP sensor voltage within the specified range? | 0.8-4 V | Go to Step 6 | Go to DTC P0106 | |||||||
Does the MAP sensor kPa change smoothly and gradually as engine speed is increased and returned to idle? | -- | Go to Step 7 | Go to DTC P0106 | |||||||
Caution: Turn OFF the ignition before inserting fingers into the throttle bore. Unexpected movement of the throttle blade could cause personal injury.
Did you find and correct the condition? | -- | Go to Step 6 | Go to Diagnostic Aids | |||||||
8 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 7 | ||||||
Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK | ||||||||
