The electronic brake control module (EBCM) supplies 5 volts to the yaw rate sensor/lateral accelerometer. When the vehicle is not moving, or is being driven in a stable, straight line, yaw rate is 0 degrees/second and the yaw rate sensor signal voltage is very near 2.5 volts. This is referred to as sensor bias voltage. Performing a turning maneuver causes the yaw rate sensor signal voltage to increase, or decrease, depending on the direction of the turn. The sharper the turn, the greater the change in signal voltage. Since the yaw rate signal is affected by temperature, the EBCM also monitors a Hz frequency signal from the yaw rate sensor/lateral accelerometer which is proportionate to the approximate temperature of the yaw rate sensor.
• | The ignition is ON. |
• | The Vehicle Stability Enhancement System (VSES) sensors have been successfully initialized or the message center has displayed the stability system disabled message due to an unsuccessful initialization attempt. Refer to ABS Description and Operation for a complete explanation of VSES sensor initialization. |
• | The vehicle is being driven relatively straight and level at a speed greater than 11 km/h (7 mph), before performing a stable turning maneuver. |
Any of the following conditions may cause the DTC to set.
• | Open yaw rate sensor circuitry is detected. |
• | Shorted yaw rate sensor circuitry is detected. |
• | An erratic yaw rate sensor signal is detected. |
• | The EBCM detects that the yaw rate sensor signal does not correspond with signals from other sensors. |
• | The EBCM detects that the yaw rate sensor frequency signal is not within the valid range. |
• | A voltage near 5 volts is detected on the yaw rate sensor test circuit at all times. |
• | A voltage near 0 volts is detected on the yaw rate sensor test circuit at all times. |
• | The EBCM disables the VSES. |
• | The message center displays the service stability system message. |
The conditions for setting the DTC are no longer present and you use the scan tool Clear DTCs function.
• | The following scenario may cause this DTC to set when no actual malfunction exists. |
- | The vehicle is driven in a straight line in reverse at a speed greater than 13 km/h (8 mph). |
- | The transmission is shifted into neutral while the vehicle continues to coast backward. |
- | A turning maneuver is performed after the above conditions are met and the vehicle speed is still greater than 13 km/h (8 mph). |
• | This DTC may also set falsely if the yaw rate sensor is replaced without first following the diagnostic table below. Whenever a new yaw rate sensor is installed, the old sensor must be disconnected, the ignition turned ON for 5 seconds and then OFF, and then the new sensor connected. |
• | Inspect the vehicle for proper wheel alignment. Ensure the vehicle does not pull toward the left or right while driving straight forward on a level surface. |
• | Communicate with the customer to determine the conditions under which the message center displays the service stability system message. Learning the conditions under which the DTC sets may help you duplicate the failure. |
• | Use the Snapshot function on the scan tool in order to assist you in locating an intermittent malfunction. |
The number below refer to the step number on the diagnostic table.
Step | Action | Values | Yes | No | ||||||
---|---|---|---|---|---|---|---|---|---|---|
Important: If DTC C0292 is set, diagnose C0292 before proceeding with diagnostics for C0196. Always use connector test adapters when performing tests to avoid damage to delicate connector terminals.Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Antilock Brake System Connector End Views | ||||||||||
1 | Did you perform the Antilock Brake System (ABS) Diagnostic System Check? | -- | Go to Step 2 | |||||||
2 |
Does the DTC reset? | -- | Go to Step 3 | Go to Diagnostic Aids | ||||||
3 |
Is the Yaw Rate Sensor Input less than the specified value? | 0.6 V | Go to Step 4 | Go to Step 19 | ||||||
4 |
Is the Yaw Rate Sensor Input greater than the specified value? | 4.4 V | Go to Step 5 | Go to Step 7 | ||||||
5 |
Does the voltage measure greater than the specified value? | 4.75 V | Go to Step 9 | Go to Step 6 | ||||||
6 | Test the yaw rate sensor/lateral accelerometer low reference circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 17 | ||||||
7 | Test the yaw rate signal circuit for the following conditions.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 8 | ||||||
8 | Test the yaw rate sensor/lateral accelerometer 5-volt reference circuit for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 17 | ||||||
9 | Use a DMM to measure the voltage on the yaw rate frequency circuit. Does the voltage measure greater than the specified value? | 4.75 V | Go to Step 10 | Go to Step 13 | ||||||
10 | Use a DMM to measure the voltage on the yaw rate sensor test circuit. Does the voltage measure greater than the specified value? | 4.75 V | Go to Step 11 | Go to Step 15 | ||||||
11 |
Does the HZ frequency signal measure within the specified range? | 13.37-14.36 kHz | Go to Step 16 | Go to Step 12 | ||||||
Does the voltage measure less than the specified value? | 0.15 V | Go to Step 16 | Go to Step 14 | |||||||
13 | Test the yaw rate frequency circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 17 | ||||||
14 | Test the yaw rate frequency circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||||
15 | Test the yaw rate sensor test circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 17 | ||||||
16 |
Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 18 | ||||||
17 | Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||||
18 |
Important: The Yaw Rate Reference Table Reset Procedure must be performed when you are instructed to do so during the Yaw Rate Sensor/Lateral Accelerometer Replacement procedure. Replace the yaw rate sensor/lateral accelerometer. Refer to Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement . Did you complete the replacement? | -- | Go to Step 20 | -- | ||||||
19 |
Important: Following EBCM replacement, perform the set-up procedure for the EBCM and perform the Yaw Rate Reference Table Reset Procedure. Use the scan tool to perform the Tire Size Calibration procedure. Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Did you complete the replacement? | -- | Go to Step 20 | -- | ||||||
20 |
Does the DTC reset? | -- | Go to Step 3 | System OK |